#include &pm8150l_gpios{ //pm7150a cam_sensor_pmi_gpio { cam_sensor_front_0_vana_active: cam_sensor_front_0_vana_active { pins = "gpio9"; function = "normal"; power-source = <0>; output-low; input-disable; }; cam_sensor_front_0_vana_suspend: cam_sensor_front_0_vana_suspend { pins = "gpio9"; function = "normal"; power-source = <0>; bias-pull-down; input-disable; }; }; }; &pm7250b_gpios{ cam_sensor_pmi_gpio { cam_sensor_rear_0_avdd_active: cam_sensor_rear_0_avdd_active { pins = "gpio12"; function = "normal"; power-source = <0>; output-low; input-disable; }; cam_sensor_rear_0_avdd_suspend: cam_sensor_rear_0_avdd_suspend { pins = "gpio12"; function = "normal"; power-source = <0>; bias-pull-down; input-disable; }; }; }; &soc { led_flash_rear: qcom,camera-flash0 { cell-index = <0>; compatible = "qcom,camera-flash"; flash-source = <&pm8150l_flash0 &pm8150l_flash1>;//pm8150a_bob torch-source = <&pm8150l_torch0 &pm8150l_torch1>; switch-source = <&pm8150l_switch2>; status = "ok"; }; led_flash_rear_aux: qcom,camera-flash1 { cell-index = <1>; compatible = "qcom,camera-flash"; flash-source = <&pm8150l_flash0 &pm8150l_flash1>; torch-source = <&pm8150l_torch0 &pm8150l_torch1>; switch-source = <&pm8150l_switch2>; status = "ok"; }; led_flash_rear_micro: qcom,camera-flash2 { cell-index = <2>; compatible = "qcom,camera-flash"; flash-source = <&pm8150l_flash0 &pm8150l_flash1>; torch-source = <&pm8150l_torch0 &pm8150l_torch1>; switch-source = <&pm8150l_switch2>; status = "ok"; }; qcom,cam-res-mgr { compatible = "qcom,cam-res-mgr"; status = "ok"; }; camera_vdig_ldo: gpio-regulator@0 { compatible = "regulator-fixed"; reg = <0x00 0x00>; regulator-name = "camera_vdig_ldo"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-enable-ramp-delay = <135>; enable-active-high; gpio = <&tlmm 72 0>; pinctrl-names = "default"; pinctrl-0 = <&cam_sensor_rear_vdig>; vin-supply = <&pm8150a_s8>; }; }; &pm8008_regulators { vdd_l6-supply = <&BOB>; vdd_l7-supply = <&BOB>; }; &L6P { regulator-max-microvolt = <2800000>; /* Reduced the headroom by 16mV for AHC */ qcom,min-dropout-voltage = <184000>; }; &L7P { regulator-max-microvolt = <2900000>; /* Reduced the headroom by 16mV for AHC */ qcom,min-dropout-voltage = <200000>; }; &pm8150_s5 { regulator-min-microvolt = <2024000>; regulator-max-microvolt = <2024000>; }; &cam_cci0 { actuator_rear_0: qcom,actuator@0 { cell-index = <0>; compatible = "qcom,actuator"; cci-master = <0>; cam_vaf-supply = <&L6P>; regulator-names = "cam_vaf"; rgltr-cntrl-support; rgltr-min-voltage = <2800000>; rgltr-max-voltage = <2800000>; rgltr-load-current = <300000>; }; ois_rear_0: qcom,ois@0{ cell-index = <0>; reg = <0>; compatible = "qcom,ois"; cam_vio-supply = <&pm8150_l17>; cam_vdig-supply = <&camera_vdig_ldo>; cam_vaf-supply = <&L3P>; regulator-names ="cam_vio","cam_vdig","cam_vaf"; rgltr-cntrl-support; rgltr-min-voltage = <0 696000 2800000>; rgltr-max-voltage = <0 1416000 2800000>; rgltr-load-current = <0 1000000 300000>; cci-master = <0>; status = "ok"; ois_gyro,position=<3>; ois,type=<0>; ois_gyro,type=<3>; ois,name="LC898124"; ois_module,vendor=<0>; ois_actuator,vednor=<0>; ois,fw=<1>; }; eeprom_rear_0: qcom,eeprom@0 { cell-index = <0>; compatible = "qcom,eeprom"; reg = <0x0>; cam_vio-supply = <&pm8150_l17>; //pm7250_l17 cam_vdig-supply = <&camera_vdig_ldo>; cam_vana-supply = <&L7P>; //pm8008_l7 cam_v_custom1-supply = <&pm8150_s5>; cam_clk-supply = <&titan_top_gdsc>; regulator-names = "cam_vio","cam_vdig","cam_vana","cam_v_custom1", "cam_clk"; rgltr-cntrl-support; rgltr-min-voltage = <0 696000 2900000 2024000 0>; rgltr-max-voltage = <0 1416000 2900000 2024000 0>; rgltr-load-current = <0 1000000 300000 300000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_rear_0_clock_active &cam_sensor_rear_0_reset_active &cam_sensor_rear_0_avdd_active>; pinctrl-1 = <&cam_sensor_rear_0_clock_suspend &cam_sensor_rear_0_reset_suspend &cam_sensor_rear_0_avdd_suspend>; gpios = <&tlmm 15 0>, <&tlmm 30 0>, <&pm7250b_gpios 12 GPIO_ACTIVE_HIGH>; use-shared-clk; gpio-reset = <1>; gpio-custom1 = <2>; gpio-req-tbl-num = <0 1 2>; gpio-req-tbl-flags = <1 0 0>; gpio-req-tbl-label = "CAM_MCLK0", "CAM_RESET0", "CAM_CUSTOM1"; sensor-mode = <0>; cci-master = <0>; status = "ok"; clocks = <&camcc CAM_CC_MCLK2_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; eeprom_rear_1: qcom,eeprom@1 { cell-index = <1>; compatible = "qcom,eeprom"; reg = <0x01>; cam_vio-supply = <&pm8150_l17>; cam_vana-supply = <&L4P>; cam_vdig-supply = <&L1P>; cam_clk-supply = <&titan_top_gdsc>; regulator-names = "cam_vio", "cam_vana", "cam_vdig", "cam_clk"; rgltr-cntrl-support; pwm-switch; rgltr-min-voltage = <0 2800000 1056000 0>; rgltr-max-voltage = <0 2800000 1056000 0>; rgltr-load-current = <300000 300000 600000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_rear_2_clock_active &cam_sensor_rear_2_reset_active>; pinctrl-1 = <&cam_sensor_rear_2_clock_suspend &cam_sensor_rear_2_reset_suspend>; gpios = <&tlmm 14 0>, <&tlmm 21 0>; use-shared-clk; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAMIF_MCLK2", "CAM_RESET2"; sensor-mode = <0>; cci-master = <1>; status = "ok"; clocks = <&camcc CAM_CC_MCLK1_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; eeprom_front_0: qcom,eeprom@2 { cell-index = <2>; compatible = "qcom,eeprom"; reg = <0x02>; cam_vio-supply = <&pm8150_l17>; //pm7250_l17 cam_vdig-supply = <&camera_vdig_ldo>; cam_vana-supply = <&pm8150a_bob>; cam_clk-supply = <&titan_top_gdsc>; regulator-names = "cam_vio","cam_vdig","cam_vana", "cam_clk"; rgltr-cntrl-support; rgltr-min-voltage = <0 696000 3008000 0>; rgltr-max-voltage = <0 1416000 3960000 0>; rgltr-load-current = <0 1000000 250000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_front_0_clock_active &cam_sensor_front_0_reset_active &cam_sensor_front_0_vana_active>; pinctrl-1 = <&cam_sensor_front_0_clock_suspend &cam_sensor_front_0_reset_suspend &cam_sensor_front_0_vana_suspend>; gpios = <&tlmm 25 0>, <&tlmm 29 0>, <&pm8150l_gpios 9 GPIO_ACTIVE_HIGH>; //pm7150a use-shared-clk; gpio-reset = <1>; gpio-vana = <2>; gpio-req-tbl-num = <0 1 2>; gpio-req-tbl-flags = <1 0 0>; gpio-req-tbl-label = "CAM_front_MCLK", "CAM_front_RESET", "CAM_front_VANA"; sensor-mode = <0>; cci-master = <1>; status = "ok"; clocks = <&camcc CAM_CC_MCLK4_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; /*wide camera*/ qcom,cam-sensor@0 { cell-index = <0>; compatible = "qcom,cam-sensor"; reg = <0x0>; csiphy-sd-index = <1>; sensor-position-roll = <90>; sensor-position-pitch = <0>; sensor-position-yaw = <180>; actuator-src = <&actuator_rear_0>; eeprom-src = <&eeprom_rear_0>; ois-src = <&ois_rear_0>; led-flash-src = <&led_flash_rear>; cam_vio-supply = <&pm8150_l17>; //pm7250_l17 cam_vdig-supply = <&camera_vdig_ldo>; cam_vana-supply = <&L7P>; //pm8008_l7 cam_v_custom1-supply = <&pm8150_s5>; //cam_v_custom2-supply = <&pm8009_l2>; cam_vaf-supply = <&L6P>; //pm8008_l6 cam_clk-supply = <&titan_top_gdsc>; regulator-names = "cam_vio","cam_vdig","cam_vana","cam_v_custom1","cam_vaf", "cam_clk"; rgltr-cntrl-support; rgltr-min-voltage = <0 696000 2900000 2024000 2800000 0>; rgltr-max-voltage = <0 1416000 2900000 2024000 2800000 0>; rgltr-load-current = <0 1000000 300000 300000 300000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_rear_0_clock_active &cam_sensor_rear_0_reset_active &cam_sensor_rear_0_avdd_active>; pinctrl-1 = <&cam_sensor_rear_0_clock_suspend &cam_sensor_rear_0_reset_suspend &cam_sensor_rear_0_avdd_suspend>; gpios = <&tlmm 15 0>, <&tlmm 30 0>, <&pm7250b_gpios 12 GPIO_ACTIVE_HIGH>; use-shared-clk; gpio-reset = <1>; gpio-custom1 = <2>; gpio-req-tbl-num = <0 1 2>; gpio-req-tbl-flags = <1 0 0>; gpio-req-tbl-label = "CAM_MCLK0", "CAM_RESET0", "CAM_CUSTOM1"; sensor-mode = <0>; cci-master = <0>; status = "ok"; clocks = <&camcc CAM_CC_MCLK2_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; /*ultra wide-rear-hi846-8M*/ qcom,cam-sensor@1 { cell-index = <1>; compatible = "qcom,cam-sensor"; reg = <0x01>; csiphy-sd-index = <3>; sensor-position-roll = <270>; sensor-position-pitch = <0>; sensor-position-yaw = <180>; eeprom-src = <&eeprom_rear_1>; led-flash-src = <&led_flash_rear_aux>; cam_vio-supply = <&pm8150_l17>; cam_vana-supply = <&L4P>; cam_vdig-supply = <&L1P>; cam_clk-supply = <&titan_top_gdsc>; regulator-names = "cam_vio", "cam_vana", "cam_vdig", "cam_clk"; rgltr-cntrl-support; pwm-switch; rgltr-min-voltage = <0 2800000 1056000 0>; rgltr-max-voltage = <0 2800000 1056000 0>; rgltr-load-current = <300000 300000 600000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_rear_2_clock_active &cam_sensor_rear_2_reset_active>; pinctrl-1 = <&cam_sensor_rear_2_clock_suspend &cam_sensor_rear_2_reset_suspend>; gpios = <&tlmm 14 0>, <&tlmm 21 0>; use-shared-clk; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAMIF_MCLK2", "CAM_RESET2"; sensor-mode = <0>; cci-master = <1>; status = "ok"; clocks = <&camcc CAM_CC_MCLK1_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; /*Front Main-IMX616-32M*/ qcom,cam-sensor@2 { cell-index = <2>; compatible = "qcom,cam-sensor"; reg = <0x02>; csiphy-sd-index = <0>; sensor-position-roll = <270>; sensor-position-pitch = <0>; sensor-position-yaw = <0>; eeprom-src = <&eeprom_front_0>; cam_vio-supply = <&pm8150_l17>; //pm7250_l17 cam_vdig-supply = <&camera_vdig_ldo>; cam_vana-supply = <&pm8150a_bob>; cam_clk-supply = <&titan_top_gdsc>; regulator-names = "cam_vio","cam_vdig","cam_vana", "cam_clk"; rgltr-cntrl-support; rgltr-min-voltage = <0 696000 3008000 0>; rgltr-max-voltage = <0 1416000 3960000 0>; rgltr-load-current = <0 1000000 250000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_front_0_clock_active &cam_sensor_front_0_reset_active &cam_sensor_front_0_vana_active>; pinctrl-1 = <&cam_sensor_front_0_clock_suspend &cam_sensor_front_0_reset_suspend &cam_sensor_front_0_vana_suspend>; gpios = <&tlmm 25 0>, <&tlmm 29 0>, <&pm8150l_gpios 9 GPIO_ACTIVE_HIGH>; //pm7150a use-shared-clk; gpio-reset = <1>; gpio-vana = <2>; gpio-req-tbl-num = <0 1 2>; gpio-req-tbl-flags = <1 0 0>; gpio-req-tbl-label = "CAM_front_MCLK", "CAM_front_RESET", "CAM_front_VANA"; sensor-mode = <0>; cci-master = <1>; status = "ok"; clocks = <&camcc CAM_CC_MCLK4_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; }; &cam_cci1 { eeprom_rear_3: qcom,eeprom@3 { cell-index = <3>; compatible = "qcom,eeprom"; reg = <0x3>; cam_vio-supply = <&pm8150_l17>; cam_vana-supply = <&L5P>; cam_clk-supply = <&titan_top_gdsc>; regulator-names = "cam_vio","cam_vana", "cam_clk"; rgltr-cntrl-support; pwm-switch; rgltr-min-voltage = <0 2800000 0>; rgltr-max-voltage = <0 2800000 0>; rgltr-load-current = <300000 300000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_rear_1_clock_active &cam_sensor_rear_1_reset_active>; pinctrl-1 = <&cam_sensor_rear_1_clock_suspend &cam_sensor_rear_1_reset_suspend>; gpios = <&tlmm 16 0>, <&tlmm 23 0>; use-shared-clk; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAM_MCLK1", "CAM_RESET1"; sensor-mode = <0>; cci-master = <0>; status = "ok"; clocks = <&camcc CAM_CC_MCLK3_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; eeprom_rear_4: qcom,eeprom@4 { cell-index = <4>; compatible = "qcom,eeprom"; reg = <0x4>; cam_vio-supply = <&pm8150_l17>; cam_vdig-supply = <&L2P>; cam_vana-supply = <&L5P>; cam_clk-supply = <&titan_top_gdsc>; regulator-names = "cam_vio","cam_vdig","cam_vana", "cam_clk"; rgltr-cntrl-support; rgltr-min-voltage = <0 1104000 2800000 0>; rgltr-max-voltage = <0 1104000 2800000 0>; rgltr-load-current = <0 1056000 800000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_rear_3_clock_active &cam_sensor_rear_3_reset_active>; pinctrl-1 = <&cam_sensor_rear_3_clock_suspend &cam_sensor_rear_3_reset_suspend>; gpios = <&tlmm 13 0>, <&tlmm 32 0>; use-shared-clk; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAM_MCLK3", "CAM_RESET3"; sensor-mode = <0>; cci-master = <0>; status = "ok"; clocks = <&camcc CAM_CC_MCLK0_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; /*macro_camera*/ qcom,cam-sensor@3 { cell-index = <3>; compatible = "qcom,cam-sensor"; reg = <0x3>; csiphy-sd-index = <2>; sensor-position-roll = <90>; sensor-position-pitch = <0>; sensor-position-yaw = <180>; eeprom-src = <&eeprom_rear_3>; led-flash-src = <&led_flash_rear_micro>; cam_vio-supply = <&pm8150_l17>; cam_vana-supply = <&L5P>; cam_clk-supply = <&titan_top_gdsc>; regulator-names = "cam_vio","cam_vana", "cam_clk"; rgltr-cntrl-support; pwm-switch; rgltr-min-voltage = <0 2800000 0>; rgltr-max-voltage = <0 2800000 0>; rgltr-load-current = <300000 300000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_rear_1_clock_active &cam_sensor_rear_1_reset_active>; pinctrl-1 = <&cam_sensor_rear_1_clock_suspend &cam_sensor_rear_1_reset_suspend>; gpios = <&tlmm 16 0>, <&tlmm 23 0>; use-shared-clk; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAM_MCLK1", "CAM_RESET1"; sensor-mode = <0>; cci-master = <0>; status = "ok"; clocks = <&camcc CAM_CC_MCLK3_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; /* IR Rear camera: gc5035*/ qcom,cam-sensor@4 { cell-index = <4>; compatible = "qcom,cam-sensor"; reg = <0x4>; csiphy-sd-index = <2>; sensor-position-roll = <90>; sensor-position-pitch = <0>; sensor-position-yaw = <180>; cam_vio-supply = <&pm8150_l17>; cam_vdig-supply = <&L2P>; cam_vana-supply = <&L5P>; cam_clk-supply = <&titan_top_gdsc>; eeprom-src = <&eeprom_rear_4>; regulator-names = "cam_vio","cam_vdig","cam_vana", "cam_clk"; rgltr-cntrl-support; rgltr-min-voltage = <0 1104000 2800000 0>; rgltr-max-voltage = <0 1104000 2800000 0>; rgltr-load-current = <0 1056000 800000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_rear_3_clock_active &cam_sensor_rear_3_reset_active>; pinctrl-1 = <&cam_sensor_rear_3_clock_suspend &cam_sensor_rear_3_reset_suspend>; gpios = <&tlmm 13 0>, <&tlmm 32 0>; use-shared-clk; gpio-reset = <1>; gpio-req-tbl-num = <0 1>; gpio-req-tbl-flags = <1 0>; gpio-req-tbl-label = "CAM_MCLK3", "CAM_RESET3"; sensor-mode = <0>; cci-master = <0>; status = "ok"; clocks = <&camcc CAM_CC_MCLK0_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; //front camera-gc8054-8M qcom,cam-sensor@5 { cell-index = <5>; compatible = "qcom,cam-sensor"; reg = <0x05>; csiphy-sd-index = <3>; sensor-position-roll = <270>; sensor-position-pitch = <0>; sensor-position-yaw = <0>; eeprom-src = <&eeprom_rear_4>; cam_vio-supply = <&pm8150_l17>; cam_vdig-supply = <&L2P>; cam_vana-supply = <&pm8150a_bob>; cam_clk-supply = <&titan_top_gdsc>; regulator-names = "cam_vio","cam_vdig","cam_vana", "cam_clk"; rgltr-cntrl-support; rgltr-min-voltage = <0 1104000 3008000 0>; rgltr-max-voltage = <0 1104000 3960000 0>; rgltr-load-current = <300000 600000 300000 0>; gpio-no-mux = <0>; pinctrl-names = "cam_default", "cam_suspend"; pinctrl-0 = <&cam_sensor_front_clock_active &cam_sensor_front_reset_active &cam_sensor_front_avdd_active &cam_sensor_front_switch_active>; pinctrl-1 = <&cam_sensor_front_clock_suspend &cam_sensor_front_reset_suspend &cam_sensor_front_avdd_suspend &cam_sensor_front_switch_suspend>; gpios = <&tlmm 14 0>, <&tlmm 21 0>, <&tlmm 22 0>, <&tlmm 56 0>; use-shared-clk; gpio-reset = <1>; gpio-vana = <2>; gpio-custom1 = <3>; gpio-req-tbl-num = <0 1 2 3>; gpio-req-tbl-flags = <1 0 0 0>; gpio-req-tbl-label = "CAM_front_MCLK", "CAM_front_RESET", "CAM_front_VANA", "CAM_custom1"; sensor-mode = <0>; cci-master = <0>; status = "ok"; clocks = <&camcc CAM_CC_MCLK1_CLK>; clock-names = "cam_clk"; clock-cntl-level = "turbo"; clock-rates = <19200000>; }; }; &tlmm { cam_sensor_front_0_clock_active: cam_sensor_front_0_clock_active { /* MCLK3 */ mux { pins = "gpio25"; function = "cam_mclk"; }; config { pins = "gpio25"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_front_0_clock_suspend: cam_sensor_front_0_clock_suspend { /* MCLK3 */ mux { pins = "gpio25"; function = "cam_mclk"; }; config { pins = "gpio25"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_0_clock_active: cam_sensor_rear_0_clock_active { /* MCLK0 */ mux { pins = "gpio15"; function = "cam_mclk"; }; config { pins = "gpio15"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_0_clock_suspend: cam_sensor_rear_0_clock_suspend { /* MCLK0 */ mux { pins = "gpio15"; function = "cam_mclk"; }; config { pins = "gpio15"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_1_clock_active: cam_sensor_rear_1_clock_active { /* MCLK1 */ mux { pins = "gpio16"; function = "cam_mclk"; }; config { pins = "gpio16"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_1_clock_suspend: cam_sensor_rear_1_clock_suspend { /* MCLK1 */ mux { pins = "gpio16"; function = "cam_mclk"; }; config { pins = "gpio16"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_3_clock_active: cam_sensor_rear_3_clock_active { /* MCLK4 */ mux { pins = "gpio13"; function = "cam_mclk"; }; config { pins = "gpio13"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_3_clock_suspend: cam_sensor_rear_3_clock_suspend { /* MCLK4 */ mux { pins = "gpio13"; function = "cam_mclk"; }; config { pins = "gpio13"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_front_clock_active: cam_sensor_front_clock_active { /* MCLK2 */ mux { pins = "gpio14"; function = "cam_mclk"; }; config { pins = "gpio14"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_front_clock_suspend: cam_sensor_front_clock_suspend { /* MCLK2 */ mux { pins = "gpio14"; function = "cam_mclk"; }; config { pins = "gpio14"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_2_clock_active: cam_sensor_rear_2_clock_active { /* MCLK4 */ mux { pins = "gpio14"; function = "cam_mclk"; }; config { pins = "gpio14"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_2_clock_suspend: cam_sensor_rear_2_clock_suspend { /* MCLK4 */ mux { pins = "gpio14"; function = "cam_mclk"; }; config { pins = "gpio14"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_front_0_reset_active: cam_sensor_front_0_reset_active { /* RESET 2 */ mux { pins = "gpio29"; function = "gpio"; }; config { pins = "gpio29"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_front_0_reset_suspend: cam_sensor_front_0_reset_suspend { /* RESET 2 */ mux { pins = "gpio29"; function = "gpio"; }; config { pins = "gpio29"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ output-low; }; }; cam_sensor_rear_0_reset_active: cam_sensor_rear_0_reset_active { /* RESET, STANDBY */ mux { pins = "gpio30"; function = "gpio"; }; config { pins = "gpio30"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_0_reset_suspend: cam_sensor_rear_0_reset_suspend { /* RESET, STANDBY */ mux { pins = "gpio30"; function = "gpio"; }; config { pins = "gpio30"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_1_reset_active: cam_sensor_rear_1_reset_active { /* RESET, STANDBY */ mux { pins = "gpio23"; function = "gpio"; }; config { pins = "gpio23"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_1_reset_suspend: cam_sensor_rear_1_reset_suspend { /* RESET, STANDBY */ mux { pins = "gpio23"; function = "gpio"; }; config { pins = "gpio23"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_vdig: cam_sensor_rear_vdig { pins = "gpio72"; function = "normal"; power-source = <0>; drive-push-pull; output-low; }; cam_sensor_rear_1_avdd_active: cam_sensor_rear_1_avdd_active { /* RESET, STANDBY */ mux { pins = "gpio139"; function = "gpio"; }; config { pins = "gpio139"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_1_avdd_suspend: cam_sensor_rear_1_avdd_suspend { /* RESET, STANDBY */ mux { pins = "gpio139"; function = "gpio"; }; config { pins = "gpio139"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_front_reset_active: cam_sensor_front_reset_active { /* RESET 2 */ mux { pins = "gpio21"; function = "gpio"; }; config { pins = "gpio21"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_front_reset_suspend: cam_sensor_front_reset_suspend { /* RESET 2 */ mux { pins = "gpio21"; function = "gpio"; }; config { pins = "gpio21"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ output-low; }; }; cam_sensor_front_switch_active: cam_sensor_front_switch_active { /* switch */ mux { pins = "gpio56"; function = "gpio"; }; config { pins = "gpio56"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_front_switch_suspend: cam_sensor_front_switch_suspend { /* switch */ mux { pins = "gpio56"; function = "gpio"; }; config { pins = "gpio56"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ output-low; }; }; cam_sensor_front_avdd_active: cam_sensor_front_avdd_active { /* RESET 2 */ mux { pins = "gpio22"; function = "gpio"; }; config { pins = "gpio22"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_front_avdd_suspend: cam_sensor_front_avdd_suspend { /* RESET 2 */ mux { pins = "gpio22"; function = "gpio"; }; config { pins = "gpio22"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ output-low; }; }; cam_sensor_rear_2_reset_active: cam_sensor_rear_2_reset_active { /* RESET, STANDBY */ mux { pins = "gpio21"; function = "gpio"; }; config { pins = "gpio21"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_2_reset_suspend: cam_sensor_rear_2_reset_suspend { /* RESET, STANDBY */ mux { pins = "gpio21"; function = "gpio"; }; config { pins = "gpio21"; bias-pull-down; /* PULL DOWN */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_2_vaf_active: cam_sensor_rear_2_vaf_active { /* RESET, STANDBY */ mux { pins = "gpio159"; function = "gpio"; }; config { pins = "gpio159"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_2_vaf_suspend: cam_sensor_rear_2_vaf_suspend { /* RESET, STANDBY */ mux { pins = "gpio159"; function = "gpio"; }; config { pins = "gpio159"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_3_reset_active: cam_sensor_rear_3_reset_active { /* RESET, STANDBY */ mux { pins = "gpio32"; function = "gpio"; }; config { pins = "gpio32"; bias-pull-down; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_3_reset_suspend: cam_sensor_rear_3_reset_suspend { /* RESET, STANDBY */ mux { pins = "gpio32"; function = "gpio"; }; config { pins = "gpio32"; bias-disable; /* No PULL */ drive-strength = <2>; /* 2 MA */ }; }; cam_sensor_rear_0_avdd2_active: cam_sensor_rear_0_avdd2_active { /* RESET, STANDBY */ mux { pins = "gpio156"; function = "gpio"; }; config { pins = "gpio156"; drive-strength = <16>; /* 2 MA */ output-high; bias-pull-up; }; }; cam_sensor_rear_0_avdd2_suspend: cam_sensor_rear_0_avdd2_suspend { /* RESET, STANDBY */ mux { pins = "gpio156"; function = "gpio"; }; config { pins = "gpio156"; output-low; /* active low reset */ bias-pull-down; drive-strength = <2>; /* 2 MA */ }; }; };