/ { }; #include "display/dsi-panel-oplus20813samsung-ams643ye01-1080-2400-dsi-cmd.dtsi" //#include "lagoon_camera/lagoon-camera-sensor-mtp.dtsi" #include &qupv3_se0_i2c { status = "ok"; Focaltech20813@38 { compatible = "focaltech,fts"; reg = <0x38>; chip-name = "FT3518"; /* Interrupt && Irq-gpio */ interrupt-parent = <&tlmm>; interrupts = <22 0x2002>; /* Power Config */ vdd_2v8-supply = <&L11E>; vcc_1v8-supply = <&L1E>; vdd_2v8_volt = <3100000>; /* Other HW Resource */ irq-gpio = <&tlmm 22 0x2002>; reset-gpio = <&tlmm 21 0x1>; pinctrl-names = "default"; pinctrl-0 = <&ts_int_active &ts_reset_active>; vid_len = <2>; tp_type = <8>; platform_support_project = <20813>; platform_support_project_dir = <20813>; platform_support_project_commandline = "default_commandline", "default_commandline"; platform_support_project_external_name = "AA058", "AA058"; touchpanel,max-num-support = <10>; touchpanel,tx-rx-num = <16 34>; touchpanel,panel-coords = <4320 9600>; touchpanel,display-coords = <1080 2400>; touchpanel,touchmajor-limit = <0 216>; touchpanel,report-rate = <120 180>; touchpanel,smooth-level = <255 2 15 25 45 60>; touchpanel,smooth-level-charging = <255 15 20 25 45 60>; touchpanel,sensitive-level = <255 20 16 13 10 5>; touchpanel,single-optimized-time = <8>; /* SW Support Feature Control */ black_gesture_support; fw_edge_limit_support; pressure_report_support; charger_pump_support; game_switch_support; smart_gesture_support; fw_update_app_support; fingerprint_underscreen_support; headset_pump_support; irq_need_dev_resume_ok; health_monitor_v2_support; high_resolution_support; lcd_tp_refresh_support; /* *Virtual Key Config: *1:touchpanel,button-type: *virtualkey_type: *Type 1: using board_properties *Type 2: using same IC (button zone&& touch zone are seprate) *Type 3: using diffrent IC (button zone&& touch zone are seprate) *Type 4: No need of virtual key process *supportted_button-map:select|menu|home|back * *2:touchpanel,button-map *type (X1,Y1)(X2,Y2)(X3,Y3)(Width_X,Hight_Y)--Only when button-type is 0 */ touchpanel,button-type = <4>; touchpanel.button-TRx = <0 0>; }; }; //#ifdef VENDOR_EDIT &soc { gpio_keys { pinctrl-0 = <&key_vol_up_default &key_vol_down_default>; vol_down { label = "volume_down"; gpios = <&pm7250b_gpios 3 GPIO_ACTIVE_LOW>; linux,input-type = <1>; linux,code = ; gpio-key,wakeup; debounce-interval = <15>; linux,can-disable; }; }; //#ifdef OPLUS_FEATURE_THERMAL_HORAE shell_front { compatible = "oplus,shell-temp"; }; shell_frame { compatible = "oplus,shell-temp"; }; shell_back { compatible = "oplus,shell-temp"; }; //#endif /* OPLUS_FEATURE_THERMAL_HORAE */ }; &pm7250b_gpios { key_vol_down { key_vol_down_default: key_vol_down_default { pins = "gpio3"; function = "normal"; input-enable; bias-pull-up; power-source = <0>; }; }; }; //#endif &pm7250b_charger { status = "ok"; io-channels = <&pm7250b_vadc ADC_USB_IN_V_16>, <&pm7250b_vadc ADC_USB_IN_I>, <&pm7250b_vadc ADC_CHG_TEMP>, <&pm7250b_vadc ADC_AMUX_THM4_PU2>, //#endif <&pm7250b_vadc ADC_DIE_TEMP>, <&pm7250b_vadc ADC_AMUX_THM3_PU2>, <&pm7250b_vadc ADC_SBUx>, <&pm7250b_vadc ADC_VPH_PWR>, <&pm7250b_vadc ADC_AMUX_THM1_PU2>; io-channel-names = "usb_in_voltage", "usb_in_current", "chg_temp", "usb_temp_l", //#endif "die_temp", "usb_temp_r", //#else //"conn_temp", //#endif "sbux_res", "vph_voltage", "skin_temp"; qcom,battery-data = <&mtp_batterydata>; qcom,sec-charger-config = <1>; qcom,auto-recharge-soc = <98>; qcom,step-charging-enable; qcom,sw-jeita-enable; qcom,charger-temp-max = <800>; qcom,smb-temp-max = <800>; qcom,suspend-input-on-debug-batt; qcom,fcc-stepping-enable; qcom,fcc-step-delay-ms = <100>; qcom,fcc-step-size-ua = <100000>; qcom,smb-internal-pull-kohm = <0>; qcom,en-skin-therm-mitigation; qcom,hvdcp3-standalone-config; qcom,misc@1600 { reg = <0x1600 0x100>; interrupts = <0x2 0x16 0x0 IRQ_TYPE_EDGE_RISING>, <0x2 0x16 0x1 IRQ_TYPE_EDGE_RISING>, <0x2 0x16 0x2 IRQ_TYPE_EDGE_RISING>, <0x2 0x16 0x5 IRQ_TYPE_EDGE_RISING>; interrupt-names = "wdog-snarl", "wdog-bark", "aicl-fail", "imp-trigger"; }; }; &pm7250b_qg { status = "ok"; io-channels = <&pm7250b_vadc ADC_BAT_THERM_PU1>, <&pm7250b_vadc ADC_BAT_ID_PU2>; io-channel-names = "batt-therm", "batt-id"; qcom,qg-iterm-ma = <300>; qcom,qg-fast-chg-config; qcom,hold-soc-while-full; qcom,linearize-soc; qcom,cl-feedback-on; qcom,tcss-enable; qcom,tcss-entry-soc = <98>; qcom,fvss-enable; qcom,fvss-vbatt-mv = <3300>; qcom,bass-enable; qcom,qg-ext-sns; qcom,s3-entry-ibat-ua = <35000>; qcom,s3-exit-ibat-ua = <65000>; //qcom,use-cp-iin-sns; qcom,ignore-shutdown-soc-secs = <7200>; qcom,shutdown-temp-diff = <200>; qcom,pm7250b-qg-feture; }; &soc { ssusb@a600000 { qcom,core-clk-rate = <200000000>; qcom,msm-bus,vectors-KBps = , , , , , , , , , , , ; dwc3@a600000 { //#ifndef OPLUS_FEATRUE_CHG_BASIC //usb-phy = <&qusb_phy0>, <&usb_qmp_dp_phy>; //#else usb-phy = <&qusb_phy0>, <&usb_nop_phy>; //#endif //#ifdef OPLUS_FEATRUE_CHG_BASIC xhci-imod-value = <160>; qcom,pm-qos-latency= <62>; //#endif //#ifndef OPLUS_FEATRUE_CHG_BASIC //maximum-speed = "super-speed"; //#else maximum-speed = "high-speed"; //#endif }; }; usb_qmp_dp_phy { //#ifndef OPLUS_FEATRUE_CHG_BASIC //status = "ok"; //#else status = "disabled"; //endif }; }; &spmi_bus { qcom,pm7250b@2 { vadc@3100 { //#ifdef VENDOR_EDIT qcom,pmic-revid = <&pm7250b_revid>; //#endif }; pm7250b_bcl { //#ifdef VENDOR_EDIT status = "disabled"; //#endif }; bcl_soc { //#ifdef VENDOR_EDIT status = "disabled"; //#endif }; }; }; &qusb_phy0 { qcom,qusb-phy-init-seq = /* */ <0x23 0x210 /* PWR_CTRL1 */ 0x03 0x04 /* PLL_ANALOG_CONTROLS_TWO */ 0x7c 0x18c /* PLL_CLOCK_INVERTERS */ 0x80 0x2c /* PLL_CMODE */ 0x0a 0x184 /* PLL_LOCK_DELAY */ 0x19 0xb4 /* PLL_DIGITAL_TIMERS_TWO */ 0x40 0x194 /* PLL_BIAS_CONTROL_1 */ 0x15 0x198 /* PLL_BIAS_CONTROL_2 */ 0x21 0x214 /* PWR_CTRL2 */ 0x08 0x220 /* IMP_CTRL1 */ 0x58 0x224 /* IMP_CTRL2 */ 0x47 0x240 /* TUNE1 */ 0x2b 0x244 /* TUNE2 */ 0xca 0x248 /* TUNE3 */ 0x04 0x24c /* TUNE4 */ 0x03 0x250 /* TUNE5 */ 0x30 0x23c /* CHG_CTRL2 */ 0x22 0x210>; /* PWR_CTRL1 */ qcom,qusb-phy-host-init-seq = /* */ <0x23 0x210 /* PWR_CTRL1 */ 0x03 0x04 /* PLL_ANALOG_CONTROLS_TWO */ 0x7c 0x18c /* PLL_CLOCK_INVERTERS */ 0x80 0x2c /* PLL_CMODE */ 0x0a 0x184 /* PLL_LOCK_DELAY */ 0x19 0xb4 /* PLL_DIGITAL_TIMERS_TWO */ 0x40 0x194 /* PLL_BIAS_CONTROL_1 */ 0x16 0x198 /* PLL_BIAS_CONTROL_2 */ 0x21 0x214 /* PWR_CTRL2 */ 0x08 0x220 /* IMP_CTRL1 */ 0x58 0x224 /* IMP_CTRL2 */ 0x47 0x240 /* TUNE1 */ 0x2b 0x244 /* TUNE2 */ 0xca 0x248 /* TUNE3 */ 0x04 0x24c /* TUNE4 */ 0x03 0x250 /* TUNE5 */ 0x30 0x23c /* CHG_CTRL2 */ 0x22 0x210>; /* PWR_CTRL1 */ }; //#ifdef VENDOR_EDIT &soc { devinfo { compatible = "oplus-devinfo"; io-channels= <&pm7250b_vadc ADC_GPIO1>; io-channel-names= "vph_pwr_voltage_sub"; pinctrl-names = "default", "active", "sleep"; pinctrl-0 = <&gpio11_adc_default &ebba_unused_gpios_default>; pinctrl-1 = <&hw_id_active>; pinctrl-2 = <&hw_id_sleep>; main-sub { compatible = "hw-match, main-sub"; use_pmic_adc; adc_ranges = <0 80 81 180 181 300 301 420 421 550 551 650 651 760 761 850 851 850 951 1050 1051 1150 1151 1300>; aboard-patterns = <1 0 2>; /*main board*/ match-projects = <20813 20058 20813>; }; device_0 { compatible = "hw, devices"; label = "distribution"; hw-id0 = <&pm7250b_gpios 4 GPIO_ACTIVE_LOW>; hw-combs = <1 0>; hw-names = "Silvery", "Black/Blue"; }; }; //#ifdef OPLUS_FEATURE_TP_BASIC oplus_sim_detect { compatible = "oplus, sim_detect"; Hw,sim_det = <&tlmm 82 0>; }; //#endif /* OPLUS_FEATURE_TP_BASIC */ oplus_rf_cable { compatible = "oplus,rf_cable"; interrupt-parent = <&tlmm>; rf_cable_support_num = <1>; rf,cable0-gpio = <&tlmm 90 0>; rf,cable-support-timer = <0>; pinctrl-names = "rf_cable_active"; pinctrl-0 = <&rf_cable0_active>; }; //#endif /* VENDOR_EDIT */ }; &pm7250b_vadc { board_id { reg = ; label = "board_id_vdata"; qcom,ratiometric; qcom,pre-scaling = <1 1>; }; }; &pm7250b_gpios { hw_id_active { hw_id_active: hw_id_active { pins = "gpio4"; /* GPIO 4 */ function = "normal"; /* normal */ input-enable; bias-pull-up; power-source = <0>; /*lv 1.8V input supply */ }; }; hw_id_sleep { hw_id_sleep: hw_id_sleep { pins = "gpio4"; /* GPIO 4 */ function = "normal"; /* normal */ input-enable; bias-pull-down; power-source = <0>; /*lv 1.8V input supply */ }; }; gpio11_adc { gpio11_adc_default: gpio11_adc_default { pins = "gpio11"; /* GPIO 11 */ function = "normal"; /* normal */ bias-high-impedance; /* DISABLE GPIO11 for ADC*/ }; }; }; //#endif VENDOR_EDIT &sdhc_2 { /delete-property/ status; status = "disabled"; }; &spmi_bus { qcom,pm6350@0 { qcom,power-on@800 { qcom,pmicwd; }; }; }; &soc { dsi_panel_pwr_supply { qcom,panel-supply-entry@1 { qcom,supply-enable-load = <857000>; qcom,supply-disable-load = <0>; qcom,supply-post-on-sleep = <0>; }; }; dsi_panel_pwr_supply_vout: dsi_panel_pwr_supply_vout { #address-cells = <1>; #size-cells = <0>; qcom,panel-supply-entry@0 { reg = <0>; qcom,supply-name = "vddio"; qcom,supply-min-voltage = <1800000>; qcom,supply-max-voltage = <1800000>; qcom,supply-enable-load = <62000>; qcom,supply-disable-load = <80>; qcom,supply-post-on-sleep = <20>; }; qcom,panel-supply-entry@1 { reg = <1>; qcom,supply-name = "vdd"; qcom,supply-min-voltage = <3000000>; qcom,supply-max-voltage = <3000000>; qcom,supply-enable-load = <857000>; qcom,supply-disable-load = <0>; qcom,supply-post-on-sleep = <0>; }; qcom,panel-supply-entry@2 { reg = <2>; qcom,supply-name = "vout"; qcom,supply-min-voltage = <1500000>; qcom,supply-max-voltage = <1510000>; qcom,supply-enable-load = <857000>; qcom,supply-disable-load = <0>; qcom,supply-post-on-sleep = <0>; regular-boot-on; }; }; dsi_panel_pwr_supply_labibb: dsi_panel_pwr_supply_labibb { #address-cells = <1>; #size-cells = <0>; qcom,panel-supply-entry@0 { reg = <0>; qcom,supply-name = "vddio"; qcom,supply-min-voltage = <1800000>; qcom,supply-max-voltage = <1800000>; qcom,supply-enable-load = <62000>; qcom,supply-disable-load = <80>; qcom,supply-post-on-sleep = <20>; }; qcom,panel-supply-entry@1 { reg = <1>; qcom,supply-name = "lab"; qcom,supply-min-voltage = <4600000>; qcom,supply-max-voltage = <6000000>; qcom,supply-enable-load = <100000>; qcom,supply-disable-load = <100>; }; qcom,panel-supply-entry@2 { reg = <2>; qcom,supply-name = "ibb"; qcom,supply-min-voltage = <4600000>; qcom,supply-max-voltage = <6000000>; qcom,supply-enable-load = <100000>; qcom,supply-disable-load = <100>; qcom,supply-post-on-sleep = <20>; }; }; qcom,dsi-display-primary { vddio-supply = <&L1E>; vdd-supply = <&L8A>; //vout-supply = <&L5P>; qcom,platform-te-gpio = <&tlmm 23 0>; qcom,platform-reset-gpio = <&pm6150l_gpios 3 0>; qcom,dsi-default-panel = <&dsi_s6e3fc3_samsung_amoled_cmd>; }; qcom,dsi-display-secondary { status = "disable"; }; qcom,dp_display@ae90000 { status = "disable"; }; }; &L5P { regulator-min-microvolt = <1500000>; regulator-max-microvolt = <3400000>; //qcom,min-dropout-voltage = <300000>; regulator-boot-on; }; &L1P { regulator-min-microvolt = <528000>; regulator-max-microvolt = <1504000>; }; &L2P { regulator-min-microvolt = <528000>; regulator-max-microvolt = <1504000>; }; &L3P { regulator-min-microvolt = <1500000>; regulator-max-microvolt = <3400000>; }; &L4P { regulator-min-microvolt = <1500000>; regulator-max-microvolt = <3400000>; }; &L6P { regulator-min-microvolt = <1500000>; regulator-max-microvolt = <3400000>; }; &L7P { regulator-min-microvolt = <1500000>; regulator-max-microvolt = <3400000>; }; //#endif /*OPLUS_BUG_STABALITY*/ //#endif //#ifdef OPLUS_FEATURE_TEMP_ADAPTER &thermal_zones { board-therm-usr { polling-delay-passive = <0>; polling-delay = <0>; thermal-governor = "user_space"; thermal-sensors = <&pm6150l_adc_tm ADC_GPIO4_PU2>; wake-capable-sensor; trips { active-config0 { temperature = <125000>; hysteresis = <1000>; type = "passive"; }; }; }; msm-s-therm-usr { polling-delay-passive = <0>; polling-delay = <0>; thermal-governor = "user_space"; thermal-sensors = <&pm6150l_adc_tm_iio ADC_AMUX_THM2_PU2>; wake-capable-sensor; trips { active-config0 { temperature = <125000>; hysteresis = <1000>; type = "passive"; }; }; }; }; /* delete low battery policy for performance */ &thermal_soc_cooling_maps { /delete-node/ soc_cpu6; /delete-node/ soc_cpu7; }; &pm6150l_vadc { /delete-property/ compatible; compatible = "qcom,spmi-adc5-temp"; }; //#endif /*OPLUS_FEATURE_TEMP_ADAPTER*/ &spmi_bus { qcom,pm6350@0 { qcom,power-on@800 { qcom,pon_2 { linux,code = ; }; }; }; };