/* * Copyright (C) 2014 NXP Semiconductors, All Rights Reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. * */ #ifndef _TFA9874_TFAFIELDNAMES_H #define _TFA9874_TFAFIELDNAMES_H #define TFA9874_I2CVERSION 1 typedef enum nxpTfa9874BfEnumList { TFA9874_BF_PWDN = 0x0000, /*!< Powerdown selection */ TFA9874_BF_I2CR = 0x0010, /*!< I2C Reset - Auto clear */ TFA9874_BF_AMPE = 0x0030, /*!< Activate Amplifier */ TFA9874_BF_DCA = 0x0040, /*!< Activate DC-to-DC converter */ TFA9874_BF_INTP = 0x0071, /*!< Interrupt config */ TFA9874_BF_BYPOCP= 0x00b0, /*!< Bypass OCP */ TFA9874_BF_TSTOCP= 0x00c0, /*!< OCP testing control */ TFA9874_BF_MANSCONF= 0x0120, /*!< I2C configured */ TFA9874_BF_MANAOOSC= 0x0140, /*!< Internal osc off at PWDN */ TFA9874_BF_MUTETO= 0x01d0, /*!< Time out SB mute sequence */ TFA9874_BF_OPENMTP= 0x01e0, /*!< Control for FAIM protection */ TFA9874_BF_AUDFS = 0x0203, /*!< Sample rate (fs) */ TFA9874_BF_INPLEV= 0x0240, /*!< TDM output attenuation */ TFA9874_BF_FRACTDEL= 0x0255, /*!< V/I Fractional delay */ TFA9874_BF_REV = 0x030f, /*!< Revision info */ TFA9874_BF_REFCKEXT= 0x0401, /*!< PLL external ref clock */ TFA9874_BF_REFCKSEL= 0x0420, /*!< PLL internal ref clock */ TFA9874_BF_SSFAIME= 0x05c0, /*!< Sub-system FAIM */ TFA9874_BF_AMPOCRT= 0x0802, /*!< Amplifier on-off criteria for shutdown */ TFA9874_BF_VDDS = 0x1000, /*!< POR */ TFA9874_BF_DCOCPOK= 0x1010, /*!< DCDC OCP nmos (sticky register , clear on read) */ TFA9874_BF_OTDS = 0x1020, /*!< OTP alarm (sticky register , clear on read) */ TFA9874_BF_OCDS = 0x1030, /*!< OCP amplifier (sticky register , clear on read) */ TFA9874_BF_UVDS = 0x1040, /*!< UVP alarm (sticky register , clear on read) */ TFA9874_BF_MANALARM= 0x1050, /*!< Alarm state */ TFA9874_BF_TDMERR= 0x1060, /*!< TDM error */ TFA9874_BF_NOCLK = 0x1070, /*!< Lost clock (sticky register , clear on read) */ TFA9874_BF_DCIL = 0x1100, /*!< DCDC current limiting */ TFA9874_BF_DCDCA = 0x1110, /*!< DCDC active (sticky register , clear on read) */ TFA9874_BF_DCHVBAT= 0x1130, /*!< DCDC level 1x */ TFA9874_BF_DCH114= 0x1140, /*!< DCDC level 1.14x */ TFA9874_BF_DCH107= 0x1150, /*!< DCDC level 1.07x */ TFA9874_BF_PLLS = 0x1160, /*!< PLL lock */ TFA9874_BF_CLKS = 0x1170, /*!< Clocks stable */ TFA9874_BF_TDMLUTER= 0x1180, /*!< TDM LUT error */ TFA9874_BF_TDMSTAT= 0x1192, /*!< TDM status bits */ TFA9874_BF_MTPB = 0x11c0, /*!< MTP busy */ TFA9874_BF_SWS = 0x11d0, /*!< Amplifier engage */ TFA9874_BF_AMPS = 0x11e0, /*!< Amplifier enable */ TFA9874_BF_AREFS = 0x11f0, /*!< References enable */ TFA9874_BF_OCPOAP= 0x1300, /*!< OCPOK pmos A */ TFA9874_BF_OCPOAN= 0x1310, /*!< OCPOK nmos A */ TFA9874_BF_OCPOBP= 0x1320, /*!< OCPOK pmos B */ TFA9874_BF_OCPOBN= 0x1330, /*!< OCPOK nmos B */ TFA9874_BF_OVDS = 0x1380, /*!< OVP alarm */ TFA9874_BF_CLIPS = 0x1390, /*!< Amplifier clipping */ TFA9874_BF_ADCCR = 0x13a0, /*!< Control ADC */ TFA9874_BF_MANWAIT1= 0x13c0, /*!< Wait HW I2C settings */ TFA9874_BF_MANMUTE= 0x13e0, /*!< Audio mute sequence */ TFA9874_BF_MANOPER= 0x13f0, /*!< Operating state */ TFA9874_BF_CLKOOR= 0x1420, /*!< External clock status */ TFA9874_BF_MANSTATE= 0x1433, /*!< Device manager status */ TFA9874_BF_DCMODE= 0x1471, /*!< DCDC mode status bits */ TFA9874_BF_BATS = 0x1509, /*!< Battery voltage (V) */ TFA9874_BF_TEMPS = 0x1608, /*!< IC Temperature (C) */ TFA9874_BF_VDDPS = 0x1709, /*!< IC VDDP voltage ( 1023*VDDP/13 V) */ TFA9874_BF_TDME = 0x2040, /*!< Enable interface */ TFA9874_BF_TDMMODE= 0x2050, /*!< Slave/master */ TFA9874_BF_TDMCLINV= 0x2060, /*!< Reception data to BCK clock */ TFA9874_BF_TDMFSLN= 0x2073, /*!< FS length (master mode only) */ TFA9874_BF_TDMFSPOL= 0x20b0, /*!< FS polarity */ TFA9874_BF_TDMNBCK= 0x20c3, /*!< N-BCK's in FS */ TFA9874_BF_TDMSLOTS= 0x2103, /*!< N-slots in Frame */ TFA9874_BF_TDMSLLN= 0x2144, /*!< N-bits in slot */ TFA9874_BF_TDMBRMG= 0x2194, /*!< N-bits remaining */ TFA9874_BF_TDMDEL= 0x21e0, /*!< data delay to FS */ TFA9874_BF_TDMADJ= 0x21f0, /*!< data adjustment */ TFA9874_BF_TDMOOMP= 0x2201, /*!< Received audio compression */ TFA9874_BF_TDMSSIZE= 0x2224, /*!< Sample size per slot */ TFA9874_BF_TDMTXDFO= 0x2271, /*!< Format unused bits */ TFA9874_BF_TDMTXUS0= 0x2291, /*!< Format unused slots DATAO */ TFA9874_BF_TDMSPKE= 0x2300, /*!< Control audio tdm channel in 0 (spkr + dcdc) */ TFA9874_BF_TDMDCE= 0x2310, /*!< Control audio tdm channel in 1 (dcdc) */ TFA9874_BF_TDMCSE= 0x2330, /*!< current sense vbat temperature and vddp feedback */ TFA9874_BF_TDMVSE= 0x2340, /*!< Voltage sense vbat temperature and vddp feedback */ TFA9874_BF_TDMSPKS= 0x2603, /*!< tdm slot for sink 0 (speaker + dcdc) */ TFA9874_BF_TDMDCS= 0x2643, /*!< tdm slot for sink 1 (dcdc) */ TFA9874_BF_TDMCSS= 0x26c3, /*!< Slot Position of current sense vbat temperature and vddp feedback */ TFA9874_BF_TDMVSS= 0x2703, /*!< Slot Position of Voltage sense vbat temperature and vddp feedback */ TFA9874_BF_ISTVDDS= 0x4000, /*!< Status POR */ TFA9874_BF_ISTBSTOC= 0x4010, /*!< Status DCDC OCP */ TFA9874_BF_ISTOTDS= 0x4020, /*!< Status OTP alarm */ TFA9874_BF_ISTOCPR= 0x4030, /*!< Status ocp alarm */ TFA9874_BF_ISTUVDS= 0x4040, /*!< Status UVP alarm */ TFA9874_BF_ISTMANALARM= 0x4050, /*!< Status nanager Alarm state */ TFA9874_BF_ISTTDMER= 0x4060, /*!< Status tdm error */ TFA9874_BF_ISTNOCLK= 0x4070, /*!< Status lost clock */ TFA9874_BF_ICLVDDS= 0x4400, /*!< Clear POR */ TFA9874_BF_ICLBSTOC= 0x4410, /*!< Clear DCDC OCP */ TFA9874_BF_ICLOTDS= 0x4420, /*!< Clear OTP alarm */ TFA9874_BF_ICLOCPR= 0x4430, /*!< Clear ocp alarm */ TFA9874_BF_ICLUVDS= 0x4440, /*!< Clear UVP alarm */ TFA9874_BF_ICLMANALARM= 0x4450, /*!< clear nanager Alarm state */ TFA9874_BF_ICLTDMER= 0x4460, /*!< Clear tdm error */ TFA9874_BF_ICLNOCLK= 0x4470, /*!< Clear lost clk */ TFA9874_BF_IEVDDS= 0x4800, /*!< Enable por */ TFA9874_BF_IEBSTOC= 0x4810, /*!< Enable DCDC OCP */ TFA9874_BF_IEOTDS= 0x4820, /*!< Enable OTP alarm */ TFA9874_BF_IEOCPR= 0x4830, /*!< Enable ocp alarm */ TFA9874_BF_IEUVDS= 0x4840, /*!< Enable UVP alarm */ TFA9874_BF_IEMANALARM= 0x4850, /*!< Enable nanager Alarm state */ TFA9874_BF_IETDMER= 0x4860, /*!< Enable tdm error */ TFA9874_BF_IENOCLK= 0x4870, /*!< Enable lost clk */ TFA9874_BF_IPOVDDS= 0x4c00, /*!< Polarity por */ TFA9874_BF_IPOBSTOC= 0x4c10, /*!< Polarity DCDC OCP */ TFA9874_BF_IPOOTDS= 0x4c20, /*!< Polarity OTP alarm */ TFA9874_BF_IPOOCPR= 0x4c30, /*!< Polarity ocp alarm */ TFA9874_BF_IPOUVDS= 0x4c40, /*!< Polarity UVP alarm */ TFA9874_BF_IPOMANALARM= 0x4c50, /*!< Polarity nanager Alarm state */ TFA9874_BF_IPOTDMER= 0x4c60, /*!< Polarity tdm error */ TFA9874_BF_IPONOCLK= 0x4c70, /*!< Polarity lost clk */ TFA9874_BF_BSSCR = 0x5001, /*!< Battery Safeguard attack time */ TFA9874_BF_BSST = 0x5023, /*!< Battery Safeguard threshold voltage level */ TFA9874_BF_BSSRL = 0x5061, /*!< Battery Safeguard maximum reduction */ TFA9874_BF_VBATFLTL= 0x5080, /*!< vbat filter limit */ TFA9874_BF_BSSR = 0x50e0, /*!< Battery voltage read out */ TFA9874_BF_BSSBY = 0x50f0, /*!< Bypass battery safeguard */ TFA9874_BF_BSSS = 0x5100, /*!< Vbat prot steepness */ TFA9874_BF_HPFBYP= 0x5150, /*!< Bypass HPF */ TFA9874_BF_DPSA = 0x5170, /*!< Enable DPSA */ TFA9874_BF_CLIPCTRL= 0x5222, /*!< Clip control setting */ TFA9874_BF_AMPGAIN= 0x5257, /*!< Amplifier gain */ TFA9874_BF_SLOPEE= 0x52d0, /*!< Enables slope control */ TFA9874_BF_SLOPESET= 0x52e0, /*!< Slope speed setting (bin. coded) */ TFA9874_BF_TDMDCG= 0x6123, /*!< Second channel gain in case of stereo using a single coil. (Total gain depending on INPLEV). (In case of mono OR stereo using 2 separate DCDC channel 1 should be disabled using TDMDCE) */ TFA9874_BF_TDMSPKG= 0x6163, /*!< Total gain depending on INPLEV setting (channel 0) */ TFA9874_BF_LNMODE= 0x62e1, /*!< ctrl select mode */ TFA9874_BF_LPM1MODE= 0x64e1, /*!< low power mode control */ TFA9874_BF_TDMSRCMAP= 0x6802, /*!< tdm source mapping */ TFA9874_BF_TDMSRCAS= 0x6831, /*!< Sensed value A */ TFA9874_BF_TDMSRCBS= 0x6851, /*!< Sensed value B */ TFA9874_BF_TDMSRCACLIP= 0x6871, /*!< clip information (analog /digital) for source0 */ TFA9874_BF_TDMSRCBCLIP= 0x6891, /*!< clip information (analog /digital) for source1 */ TFA9874_BF_LP1 = 0x6e10, /*!< low power mode 1 detection */ TFA9874_BF_LA = 0x6e20, /*!< low amplitude detection */ TFA9874_BF_VDDPH = 0x6e30, /*!< vddp greater than vbat */ TFA9874_BF_DELCURCOMP= 0x6f02, /*!< delay to allign compensation signal with current sense signal */ TFA9874_BF_SIGCURCOMP= 0x6f40, /*!< polarity of compensation for current sense */ TFA9874_BF_ENCURCOMP= 0x6f50, /*!< enable current sense compensation */ TFA9874_BF_LVLCLPPWM= 0x6f72, /*!< set the amount of pwm pulse that may be skipped before clip-flag is triggered */ TFA9874_BF_DCMCC = 0x7033, /*!< Max coil current */ TFA9874_BF_DCCV = 0x7071, /*!< Slope compensation current, represents LxF (inductance x frequency) value */ TFA9874_BF_DCIE = 0x7090, /*!< Adaptive boost mode */ TFA9874_BF_DCSR = 0x70a0, /*!< Soft ramp up/down */ TFA9874_BF_DCDIS = 0x70e0, /*!< DCDC on/off */ TFA9874_BF_DCPWM = 0x70f0, /*!< DCDC PWM only mode */ TFA9874_BF_DCTRACK= 0x7430, /*!< Boost algorithm selection, effective only when boost_intelligent is set to 1 */ TFA9874_BF_DCTRIP= 0x7444, /*!< 1st Adaptive boost trip levels, effective only when DCIE is set to 1 */ TFA9874_BF_DCHOLD= 0x7494, /*!< Hold time for DCDC booster, effective only when boost_intelligent is set to 1 */ TFA9874_BF_DCTRIP2= 0x7534, /*!< 2nd Adaptive boost trip levels, effective only when DCIE is set to 1 */ TFA9874_BF_DCTRIPT= 0x7584, /*!< Track Adaptive boost trip levels, effective only when boost_intelligent is set to 1 */ TFA9874_BF_DCTRIPHYSTE= 0x75f0, /*!< Enable hysteresis on booster trip levels */ TFA9874_BF_DCVOF = 0x7635, /*!< First boost voltage level */ TFA9874_BF_DCVOS = 0x7695, /*!< Second boost voltage level */ TFA9874_BF_MTPK = 0xa107, /*!< MTP KEY2 register */ TFA9874_BF_KEY1LOCKED= 0xa200, /*!< Indicates KEY1 is locked */ TFA9874_BF_KEY2LOCKED= 0xa210, /*!< Indicates KEY2 is locked */ TFA9874_BF_CIMTP = 0xa360, /*!< Start copying data from I2C mtp registers to mtp */ TFA9874_BF_MTPRDMSB= 0xa50f, /*!< MSB word of MTP manual read data */ TFA9874_BF_MTPRDLSB= 0xa60f, /*!< LSB word of MTP manual read data */ TFA9874_BF_EXTTS = 0xb108, /*!< External temperature (C) */ TFA9874_BF_TROS = 0xb190, /*!< Select temp Speaker calibration */ TFA9874_BF_SWPROFIL= 0xee0f, /*!< Software profile data */ TFA9874_BF_SWVSTEP= 0xef0f, /*!< Software vstep information */ TFA9874_BF_MTPOTC= 0xf000, /*!< Calibration schedule */ TFA9874_BF_MTPEX = 0xf010, /*!< Calibration Ron executed */ TFA9874_BF_DCMCCAPI= 0xf020, /*!< Calibration current limit DCDC */ TFA9874_BF_DCMCCSB= 0xf030, /*!< Sign bit for delta calibration current limit DCDC */ TFA9874_BF_USERDEF= 0xf042, /*!< Calibration delta current limit DCDC */ TFA9874_BF_CUSTINFO= 0xf078, /*!< Reserved space for allowing customer to store speaker information */ TFA9874_BF_R25C = 0xf50f, /*!< Ron resistance of speaker coil */ } nxpTfa9874BfEnumList_t; #define TFA9874_NAMETABLE static tfaBfName_t Tfa9874DatasheetNames[]= {\ { 0x0, "PWDN"}, /* Powerdown selection , */\ { 0x10, "I2CR"}, /* I2C Reset - Auto clear , */\ { 0x30, "AMPE"}, /* Activate Amplifier , */\ { 0x40, "DCA"}, /* Activate DC-to-DC converter , */\ { 0x71, "INTP"}, /* Interrupt config , */\ { 0xb0, "BYPOCP"}, /* Bypass OCP , */\ { 0xc0, "TSTOCP"}, /* OCP testing control , */\ { 0x120, "MANSCONF"}, /* I2C configured , */\ { 0x140, "MANAOOSC"}, /* Internal osc off at PWDN , */\ { 0x1d0, "MUTETO"}, /* Time out SB mute sequence , */\ { 0x1e0, "OPENMTP"}, /* Control for FAIM protection , */\ { 0x203, "AUDFS"}, /* Sample rate (fs) , */\ { 0x240, "INPLEV"}, /* TDM output attenuation , */\ { 0x255, "FRACTDEL"}, /* V/I Fractional delay , */\ { 0x30f, "REV"}, /* Revision info , */\ { 0x401, "REFCKEXT"}, /* PLL external ref clock , */\ { 0x420, "REFCKSEL"}, /* PLL internal ref clock , */\ { 0x5c0, "SSFAIME"}, /* Sub-system FAIM , */\ { 0x802, "AMPOCRT"}, /* Amplifier on-off criteria for shutdown , */\ { 0x1000, "VDDS"}, /* POR , */\ { 0x1010, "DCOCPOK"}, /* DCDC OCP nmos (sticky register , clear on read) , */\ { 0x1020, "OTDS"}, /* OTP alarm (sticky register , clear on read) , */\ { 0x1030, "OCDS"}, /* OCP amplifier (sticky register , clear on read), */\ { 0x1040, "UVDS"}, /* UVP alarm (sticky register , clear on read) , */\ { 0x1050, "MANALARM"}, /* Alarm state , */\ { 0x1060, "TDMERR"}, /* TDM error , */\ { 0x1070, "NOCLK"}, /* Lost clock (sticky register , clear on read) , */\ { 0x1100, "DCIL"}, /* DCDC current limiting , */\ { 0x1110, "DCDCA"}, /* DCDC active (sticky register , clear on read) , */\ { 0x1130, "DCHVBAT"}, /* DCDC level 1x , */\ { 0x1140, "DCH114"}, /* DCDC level 1.14x , */\ { 0x1150, "DCH107"}, /* DCDC level 1.07x , */\ { 0x1160, "PLLS"}, /* PLL lock , */\ { 0x1170, "CLKS"}, /* Clocks stable , */\ { 0x1180, "TDMLUTER"}, /* TDM LUT error , */\ { 0x1192, "TDMSTAT"}, /* TDM status bits , */\ { 0x11c0, "MTPB"}, /* MTP busy , */\ { 0x11d0, "SWS"}, /* Amplifier engage , */\ { 0x11e0, "AMPS"}, /* Amplifier enable , */\ { 0x11f0, "AREFS"}, /* References enable , */\ { 0x1300, "OCPOAP"}, /* OCPOK pmos A , */\ { 0x1310, "OCPOAN"}, /* OCPOK nmos A , */\ { 0x1320, "OCPOBP"}, /* OCPOK pmos B , */\ { 0x1330, "OCPOBN"}, /* OCPOK nmos B , */\ { 0x1380, "OVDS"}, /* OVP alarm , */\ { 0x1390, "CLIPS"}, /* Amplifier clipping , */\ { 0x13a0, "ADCCR"}, /* Control ADC , */\ { 0x13c0, "MANWAIT1"}, /* Wait HW I2C settings , */\ { 0x13e0, "MANMUTE"}, /* Audio mute sequence , */\ { 0x13f0, "MANOPER"}, /* Operating state , */\ { 0x1420, "CLKOOR"}, /* External clock status , */\ { 0x1433, "MANSTATE"}, /* Device manager status , */\ { 0x1471, "DCMODE"}, /* DCDC mode status bits , */\ { 0x1509, "BATS"}, /* Battery voltage (V) , */\ { 0x1608, "TEMPS"}, /* IC Temperature (C) , */\ { 0x1709, "VDDPS"}, /* IC VDDP voltage ( 1023*VDDP/13 V) , */\ { 0x2040, "TDME"}, /* Enable interface , */\ { 0x2050, "TDMMODE"}, /* Slave/master , */\ { 0x2060, "TDMCLINV"}, /* Reception data to BCK clock , */\ { 0x2073, "TDMFSLN"}, /* FS length (master mode only) , */\ { 0x20b0, "TDMFSPOL"}, /* FS polarity , */\ { 0x20c3, "TDMNBCK"}, /* N-BCK's in FS , */\ { 0x2103, "TDMSLOTS"}, /* N-slots in Frame , */\ { 0x2144, "TDMSLLN"}, /* N-bits in slot , */\ { 0x2194, "TDMBRMG"}, /* N-bits remaining , */\ { 0x21e0, "TDMDEL"}, /* data delay to FS , */\ { 0x21f0, "TDMADJ"}, /* data adjustment , */\ { 0x2201, "TDMOOMP"}, /* Received audio compression , */\ { 0x2224, "TDMSSIZE"}, /* Sample size per slot , */\ { 0x2271, "TDMTXDFO"}, /* Format unused bits , */\ { 0x2291, "TDMTXUS0"}, /* Format unused slots DATAO , */\ { 0x2300, "TDMSPKE"}, /* Control audio tdm channel in 0 (spkr + dcdc) , */\ { 0x2310, "TDMDCE"}, /* Control audio tdm channel in 1 (dcdc) , */\ { 0x2330, "TDMCSE"}, /* current sense vbat temperature and vddp feedback , */\ { 0x2340, "TDMVSE"}, /* Voltage sense vbat temperature and vddp feedback , */\ { 0x2603, "TDMSPKS"}, /* tdm slot for sink 0 (speaker + dcdc) , */\ { 0x2643, "TDMDCS"}, /* tdm slot for sink 1 (dcdc) , */\ { 0x26c3, "TDMCSS"}, /* Slot Position of current sense vbat temperature and vddp feedback, */\ { 0x2703, "TDMVSS"}, /* Slot Position of Voltage sense vbat temperature and vddp feedback, */\ { 0x4000, "ISTVDDS"}, /* Status POR , */\ { 0x4010, "ISTBSTOC"}, /* Status DCDC OCP , */\ { 0x4020, "ISTOTDS"}, /* Status OTP alarm , */\ { 0x4030, "ISTOCPR"}, /* Status ocp alarm , */\ { 0x4040, "ISTUVDS"}, /* Status UVP alarm , */\ { 0x4050, "ISTMANALARM"}, /* Status nanager Alarm state , */\ { 0x4060, "ISTTDMER"}, /* Status tdm error , */\ { 0x4070, "ISTNOCLK"}, /* Status lost clock , */\ { 0x4400, "ICLVDDS"}, /* Clear POR , */\ { 0x4410, "ICLBSTOC"}, /* Clear DCDC OCP , */\ { 0x4420, "ICLOTDS"}, /* Clear OTP alarm , */\ { 0x4430, "ICLOCPR"}, /* Clear ocp alarm , */\ { 0x4440, "ICLUVDS"}, /* Clear UVP alarm , */\ { 0x4450, "ICLMANALARM"}, /* clear nanager Alarm state , */\ { 0x4460, "ICLTDMER"}, /* Clear tdm error , */\ { 0x4470, "ICLNOCLK"}, /* Clear lost clk , */\ { 0x4800, "IEVDDS"}, /* Enable por , */\ { 0x4810, "IEBSTOC"}, /* Enable DCDC OCP , */\ { 0x4820, "IEOTDS"}, /* Enable OTP alarm , */\ { 0x4830, "IEOCPR"}, /* Enable ocp alarm , */\ { 0x4840, "IEUVDS"}, /* Enable UVP alarm , */\ { 0x4850, "IEMANALARM"}, /* Enable nanager Alarm state , */\ { 0x4860, "IETDMER"}, /* Enable tdm error , */\ { 0x4870, "IENOCLK"}, /* Enable lost clk , */\ { 0x4c00, "IPOVDDS"}, /* Polarity por , */\ { 0x4c10, "IPOBSTOC"}, /* Polarity DCDC OCP , */\ { 0x4c20, "IPOOTDS"}, /* Polarity OTP alarm , */\ { 0x4c30, "IPOOCPR"}, /* Polarity ocp alarm , */\ { 0x4c40, "IPOUVDS"}, /* Polarity UVP alarm , */\ { 0x4c50, "IPOMANALARM"}, /* Polarity nanager Alarm state , */\ { 0x4c60, "IPOTDMER"}, /* Polarity tdm error , */\ { 0x4c70, "IPONOCLK"}, /* Polarity lost clk , */\ { 0x5001, "BSSCR"}, /* Battery Safeguard attack time , */\ { 0x5023, "BSST"}, /* Battery Safeguard threshold voltage level , */\ { 0x5061, "BSSRL"}, /* Battery Safeguard maximum reduction , */\ { 0x5080, "VBATFLTL"}, /* vbat filter limit , */\ { 0x50e0, "BSSR"}, /* Battery voltage read out , */\ { 0x50f0, "BSSBY"}, /* Bypass battery safeguard , */\ { 0x5100, "BSSS"}, /* Vbat prot steepness , */\ { 0x5150, "HPFBYP"}, /* Bypass HPF , */\ { 0x5170, "DPSA"}, /* Enable DPSA , */\ { 0x5222, "CLIPCTRL"}, /* Clip control setting , */\ { 0x5257, "AMPGAIN"}, /* Amplifier gain , */\ { 0x52d0, "SLOPEE"}, /* Enables slope control , */\ { 0x52e0, "SLOPESET"}, /* Slope speed setting (bin. coded) , */\ { 0x6123, "TDMDCG"}, /* Second channel gain in case of stereo using a single coil. (Total gain depending on INPLEV). (In case of mono OR stereo using 2 separate DCDC channel 1 should be disabled using TDMDCE), */\ { 0x6163, "TDMSPKG"}, /* Total gain depending on INPLEV setting (channel 0), */\ { 0x62e1, "LNMODE"}, /* ctrl select mode , */\ { 0x64e1, "LPM1MODE"}, /* low power mode control , */\ { 0x6802, "TDMSRCMAP"}, /* tdm source mapping , */\ { 0x6831, "TDMSRCAS"}, /* Sensed value A , */\ { 0x6851, "TDMSRCBS"}, /* Sensed value B , */\ { 0x6871, "TDMSRCACLIP"}, /* clip information (analog /digital) for source0 , */\ { 0x6891, "TDMSRCBCLIP"}, /* clip information (analog /digital) for source1 , */\ { 0x6e10, "LP1"}, /* low power mode 1 detection , */\ { 0x6e20, "LA"}, /* low amplitude detection , */\ { 0x6e30, "VDDPH"}, /* vddp greater than vbat , */\ { 0x6f02, "DELCURCOMP"}, /* delay to allign compensation signal with current sense signal, */\ { 0x6f40, "SIGCURCOMP"}, /* polarity of compensation for current sense , */\ { 0x6f50, "ENCURCOMP"}, /* enable current sense compensation , */\ { 0x6f72, "LVLCLPPWM"}, /* set the amount of pwm pulse that may be skipped before clip-flag is triggered, */\ { 0x7033, "DCMCC"}, /* Max coil current , */\ { 0x7071, "DCCV"}, /* Slope compensation current, represents LxF (inductance x frequency) value , */\ { 0x7090, "DCIE"}, /* Adaptive boost mode , */\ { 0x70a0, "DCSR"}, /* Soft ramp up/down , */\ { 0x70e0, "DCDIS"}, /* DCDC on/off , */\ { 0x70f0, "DCPWM"}, /* DCDC PWM only mode , */\ { 0x7430, "DCTRACK"}, /* Boost algorithm selection, effective only when boost_intelligent is set to 1, */\ { 0x7444, "DCTRIP"}, /* 1st Adaptive boost trip levels, effective only when DCIE is set to 1, */\ { 0x7494, "DCHOLD"}, /* Hold time for DCDC booster, effective only when boost_intelligent is set to 1, */\ { 0x7534, "DCTRIP2"}, /* 2nd Adaptive boost trip levels, effective only when DCIE is set to 1, */\ { 0x7584, "DCTRIPT"}, /* Track Adaptive boost trip levels, effective only when boost_intelligent is set to 1, */\ { 0x75f0, "DCTRIPHYSTE"}, /* Enable hysteresis on booster trip levels , */\ { 0x7635, "DCVOF"}, /* First boost voltage level , */\ { 0x7695, "DCVOS"}, /* Second boost voltage level , */\ { 0xa107, "MTPK"}, /* MTP KEY2 register , */\ { 0xa200, "KEY1LOCKED"}, /* Indicates KEY1 is locked , */\ { 0xa210, "KEY2LOCKED"}, /* Indicates KEY2 is locked , */\ { 0xa360, "CIMTP"}, /* Start copying data from I2C mtp registers to mtp , */\ { 0xa50f, "MTPRDMSB"}, /* MSB word of MTP manual read data , */\ { 0xa60f, "MTPRDLSB"}, /* LSB word of MTP manual read data , */\ { 0xb108, "EXTTS"}, /* External temperature (C) , */\ { 0xb190, "TROS"}, /* Select temp Speaker calibration , */\ { 0xee0f, "SWPROFIL"}, /* Software profile data , */\ { 0xef0f, "SWVSTEP"}, /* Software vstep information , */\ { 0xf000, "MTPOTC"}, /* Calibration schedule , */\ { 0xf010, "MTPEX"}, /* Calibration Ron executed , */\ { 0xf020, "DCMCCAPI"}, /* Calibration current limit DCDC , */\ { 0xf030, "DCMCCSB"}, /* Sign bit for delta calibration current limit DCDC , */\ { 0xf042, "USERDEF"}, /* Calibration delta current limit DCDC , */\ { 0xf078, "CUSTINFO"}, /* Reserved space for allowing customer to store speaker information, */\ { 0xf50f, "R25C"}, /* Ron resistance of speaker coil , */\ { 0xffff,"Unknown bitfield enum" } /* not found */\ }; #define TFA9874_BITNAMETABLE static tfaBfName_t Tfa9874BitNames[]= {\ { 0x0, "powerdown"}, /* Powerdown selection , */\ { 0x10, "reset"}, /* I2C Reset - Auto clear , */\ { 0x30, "enbl_amplifier"}, /* Activate Amplifier , */\ { 0x40, "enbl_boost"}, /* Activate DC-to-DC converter , */\ { 0x71, "int_pad_io"}, /* Interrupt config , */\ { 0xb0, "bypass_ocp"}, /* Bypass OCP , */\ { 0xc0, "test_ocp"}, /* OCP testing control , */\ { 0x120, "src_set_configured"}, /* I2C configured , */\ { 0x140, "enbl_osc1m_auto_off"}, /* Internal osc off at PWDN , */\ { 0x1d0, "disable_mute_time_out"}, /* Time out SB mute sequence , */\ { 0x1e0, "unprotect_faim"}, /* Control for FAIM protection , */\ { 0x203, "audio_fs"}, /* Sample rate (fs) , */\ { 0x240, "input_level"}, /* TDM output attenuation , */\ { 0x255, "cs_frac_delay"}, /* V/I Fractional delay , */\ { 0x2d0, "sel_hysteresis"}, /* Select hysteresis for clock range detector , */\ { 0x30f, "device_rev"}, /* Revision info , */\ { 0x401, "pll_clkin_sel"}, /* PLL external ref clock , */\ { 0x420, "pll_clkin_sel_osc"}, /* PLL internal ref clock , */\ { 0x5c0, "enbl_faim_ss"}, /* Sub-system FAIM , */\ { 0x802, "ctrl_on2off_criterion"}, /* Amplifier on-off criteria for shutdown , */\ { 0xe07, "ctrl_digtoana"}, /* Spare control from digital to analog , */\ { 0xf0f, "hidden_code"}, /* 5A6Bh, 23147d to access registers (default for engineering), */\ { 0x1000, "flag_por"}, /* POR , */\ { 0x1010, "flag_bst_ocpok"}, /* DCDC OCP nmos (sticky register , clear on read) , */\ { 0x1020, "flag_otpok"}, /* OTP alarm (sticky register , clear on read) , */\ { 0x1030, "flag_ocp_alarm"}, /* OCP amplifier (sticky register , clear on read), */\ { 0x1040, "flag_uvpok"}, /* UVP alarm (sticky register , clear on read) , */\ { 0x1050, "flag_man_alarm_state"}, /* Alarm state , */\ { 0x1060, "flag_tdm_error"}, /* TDM error , */\ { 0x1070, "flag_lost_clk"}, /* Lost clock (sticky register , clear on read) , */\ { 0x1100, "flag_bst_bstcur"}, /* DCDC current limiting , */\ { 0x1110, "flag_bst_hiz"}, /* DCDC active (sticky register , clear on read) , */\ { 0x1120, "flag_bst_peakcur"}, /* Indicates current is max in DC-to-DC converter , */\ { 0x1130, "flag_bst_voutcomp"}, /* DCDC level 1x , */\ { 0x1140, "flag_bst_voutcomp86"}, /* DCDC level 1.14x , */\ { 0x1150, "flag_bst_voutcomp93"}, /* DCDC level 1.07x , */\ { 0x1160, "flag_pll_lock"}, /* PLL lock , */\ { 0x1170, "flag_clocks_stable"}, /* Clocks stable , */\ { 0x1180, "flag_tdm_lut_error"}, /* TDM LUT error , */\ { 0x1192, "flag_tdm_status"}, /* TDM status bits , */\ { 0x11c0, "flag_mtp_busy"}, /* MTP busy , */\ { 0x11d0, "flag_engage"}, /* Amplifier engage , */\ { 0x11e0, "flag_enbl_amp"}, /* Amplifier enable , */\ { 0x11f0, "flag_enbl_ref"}, /* References enable , */\ { 0x1300, "flag_ocpokap"}, /* OCPOK pmos A , */\ { 0x1310, "flag_ocpokan"}, /* OCPOK nmos A , */\ { 0x1320, "flag_ocpokbp"}, /* OCPOK pmos B , */\ { 0x1330, "flag_ocpokbn"}, /* OCPOK nmos B , */\ { 0x1380, "flag_ovpok"}, /* OVP alarm , */\ { 0x1390, "flag_clip"}, /* Amplifier clipping , */\ { 0x13a0, "flag_adc10_ready"}, /* Control ADC , */\ { 0x13c0, "flag_man_wait_src_settings"}, /* Wait HW I2C settings , */\ { 0x13e0, "flag_man_start_mute_audio"}, /* Audio mute sequence , */\ { 0x13f0, "flag_man_operating_state"}, /* Operating state , */\ { 0x1420, "flag_clk_out_of_range"}, /* External clock status , */\ { 0x1433, "man_state"}, /* Device manager status , */\ { 0x1471, "status_bst_mode"}, /* DCDC mode status bits , */\ { 0x1509, "bat_adc"}, /* Battery voltage (V) , */\ { 0x1608, "temp_adc"}, /* IC Temperature (C) , */\ { 0x1709, "vddp_adc"}, /* IC VDDP voltage ( 1023*VDDP/13 V) , */\ { 0x2040, "tdm_enable"}, /* Enable interface , */\ { 0x2050, "tdm_mode"}, /* Slave/master , */\ { 0x2060, "tdm_clk_inversion"}, /* Reception data to BCK clock , */\ { 0x2073, "tdm_fs_ws_length"}, /* FS length (master mode only) , */\ { 0x20b0, "tdm_fs_ws_polarity"}, /* FS polarity , */\ { 0x20c3, "tdm_nbck"}, /* N-BCK's in FS , */\ { 0x2103, "tdm_nb_of_slots"}, /* N-slots in Frame , */\ { 0x2144, "tdm_slot_length"}, /* N-bits in slot , */\ { 0x2194, "tdm_bits_remaining"}, /* N-bits remaining , */\ { 0x21e0, "tdm_data_delay"}, /* data delay to FS , */\ { 0x21f0, "tdm_data_adjustment"}, /* data adjustment , */\ { 0x2201, "tdm_audio_sample_compression"}, /* Received audio compression , */\ { 0x2224, "tdm_sample_size"}, /* Sample size per slot , */\ { 0x2271, "tdm_txdata_format"}, /* Format unused bits , */\ { 0x2291, "tdm_txdata_format_unused_slot_sd0"}, /* Format unused slots DATAO , */\ { 0x2300, "tdm_sink0_enable"}, /* Control audio tdm channel in 0 (spkr + dcdc) , */\ { 0x2310, "tdm_sink1_enable"}, /* Control audio tdm channel in 1 (dcdc) , */\ { 0x2330, "tdm_source0_enable"}, /* current sense vbat temperature and vddp feedback , */\ { 0x2340, "tdm_source1_enable"}, /* Voltage sense vbat temperature and vddp feedback , */\ { 0x2603, "tdm_sink0_slot"}, /* tdm slot for sink 0 (speaker + dcdc) , */\ { 0x2643, "tdm_sink1_slot"}, /* tdm slot for sink 1 (dcdc) , */\ { 0x26c3, "tdm_source0_slot"}, /* Slot Position of current sense vbat temperature and vddp feedback, */\ { 0x2703, "tdm_source1_slot"}, /* Slot Position of Voltage sense vbat temperature and vddp feedback, */\ { 0x4000, "int_out_flag_por"}, /* Status POR , */\ { 0x4010, "int_out_flag_bst_ocpok"}, /* Status DCDC OCP , */\ { 0x4020, "int_out_flag_otpok"}, /* Status OTP alarm , */\ { 0x4030, "int_out_flag_ocp_alarm"}, /* Status ocp alarm , */\ { 0x4040, "int_out_flag_uvpok"}, /* Status UVP alarm , */\ { 0x4050, "int_out_flag_man_alarm_state"}, /* Status nanager Alarm state , */\ { 0x4060, "int_out_flag_tdm_error"}, /* Status tdm error , */\ { 0x4070, "int_out_flag_lost_clk"}, /* Status lost clock , */\ { 0x4400, "int_in_flag_por"}, /* Clear POR , */\ { 0x4410, "int_in_flag_bst_ocpok"}, /* Clear DCDC OCP , */\ { 0x4420, "int_in_flag_otpok"}, /* Clear OTP alarm , */\ { 0x4430, "int_in_flag_ocp_alarm"}, /* Clear ocp alarm , */\ { 0x4440, "int_in_flag_uvpok"}, /* Clear UVP alarm , */\ { 0x4450, "int_in_flag_man_alarm_state"}, /* clear nanager Alarm state , */\ { 0x4460, "int_in_flag_tdm_error"}, /* Clear tdm error , */\ { 0x4470, "int_in_flag_lost_clk"}, /* Clear lost clk , */\ { 0x4800, "int_enable_flag_por"}, /* Enable por , */\ { 0x4810, "int_enable_flag_bst_ocpok"}, /* Enable DCDC OCP , */\ { 0x4820, "int_enable_flag_otpok"}, /* Enable OTP alarm , */\ { 0x4830, "int_enable_flag_ocp_alarm"}, /* Enable ocp alarm , */\ { 0x4840, "int_enable_flag_uvpok"}, /* Enable UVP alarm , */\ { 0x4850, "int_enable_flag_man_alarm_state"}, /* Enable nanager Alarm state , */\ { 0x4860, "int_enable_flag_tdm_error"}, /* Enable tdm error , */\ { 0x4870, "int_enable_flag_lost_clk"}, /* Enable lost clk , */\ { 0x4c00, "int_polarity_flag_por"}, /* Polarity por , */\ { 0x4c10, "int_polarity_flag_bst_ocpok"}, /* Polarity DCDC OCP , */\ { 0x4c20, "int_polarity_flag_otpok"}, /* Polarity OTP alarm , */\ { 0x4c30, "int_polarity_flag_ocp_alarm"}, /* Polarity ocp alarm , */\ { 0x4c40, "int_polarity_flag_uvpok"}, /* Polarity UVP alarm , */\ { 0x4c50, "int_polarity_flag_man_alarm_state"}, /* Polarity nanager Alarm state , */\ { 0x4c60, "int_polarity_flag_tdm_error"}, /* Polarity tdm error , */\ { 0x4c70, "int_polarity_flag_lost_clk"}, /* Polarity lost clk , */\ { 0x5001, "vbat_prot_attack_time"}, /* Battery Safeguard attack time , */\ { 0x5023, "vbat_prot_thlevel"}, /* Battery Safeguard threshold voltage level , */\ { 0x5061, "vbat_prot_max_reduct"}, /* Battery Safeguard maximum reduction , */\ { 0x5080, "vbat_flt_limit"}, /* vbat filter limit , */\ { 0x50d0, "rst_min_vbat"}, /* Reset clipper - Auto clear , */\ { 0x50e0, "sel_vbat"}, /* Battery voltage read out , */\ { 0x50f0, "bypass_clipper"}, /* Bypass battery safeguard , */\ { 0x5100, "batsense_steepness"}, /* Vbat prot steepness , */\ { 0x5150, "bypass_hp"}, /* Bypass HPF , */\ { 0x5170, "enbl_dpsa"}, /* Enable DPSA , */\ { 0x5222, "ctrl_cc"}, /* Clip control setting , */\ { 0x5257, "gain"}, /* Amplifier gain , */\ { 0x52d0, "ctrl_slopectrl"}, /* Enables slope control , */\ { 0x52e0, "ctrl_slope"}, /* Slope speed setting (bin. coded) , */\ { 0x5301, "dpsa_level"}, /* DPSA threshold levels , */\ { 0x5321, "dpsa_release"}, /* DPSA Release time , */\ { 0x5340, "clipfast"}, /* Clock selection for HW clipper for Battery Safeguard, */\ { 0x5350, "bypass_lp"}, /* Bypass the low power filter inside temperature sensor, */\ { 0x5400, "first_order_mode"}, /* Overrule to 1st order mode of control stage when clipping, */\ { 0x5410, "bypass_ctrlloop"}, /* Switch amplifier into open loop configuration , */\ { 0x5430, "icomp_engage"}, /* Engage of icomp , */\ { 0x5440, "ctrl_kickback"}, /* Prevent double pulses of output stage , */\ { 0x5450, "icomp_engage_overrule"}, /* To overrule the functional icomp_engage signal during validation, */\ { 0x5503, "ctrl_dem"}, /* Enable DEM icomp and DEM one bit dac , */\ { 0x5543, "ctrl_dem_mismatch"}, /* Enable DEM icomp mismatch for testing , */\ { 0x5582, "dpsa_drive"}, /* Drive setting (bin. coded) , */\ { 0x5690, "sel_pwm_delay_src"}, /* Control for selection for PWM delay line source , */\ { 0x56a1, "enbl_odd_up_even_down"}, /* Control for PWM reference sawtooth generartion , */\ { 0x570a, "enbl_amp"}, /* Switch on the class-D power sections, each part of the analog sections can be switched on/off individually, */\ { 0x57b0, "enbl_engage"}, /* Enables/engage power stage and control loop , */\ { 0x57c0, "enbl_engage_pst"}, /* Enables/engage power stage and control loop , */\ { 0x5810, "hard_mute"}, /* Hard mute - PWM , */\ { 0x5820, "pwm_shape"}, /* PWM shape , */\ { 0x5844, "pwm_delay"}, /* PWM delay bits to set the delay, clockd is 1/(k*2048*fs), */\ { 0x5890, "reclock_pwm"}, /* Reclock the pwm signal inside analog , */\ { 0x58a0, "reclock_voltsense"}, /* Reclock the voltage sense pwm signal , */\ { 0x58c0, "enbl_pwm_phase_shift"}, /* Control for pwm phase shift , */\ { 0x6123, "ctrl_attl"}, /* Second channel gain in case of stereo using a single coil. (Total gain depending on INPLEV). (In case of mono OR stereo using 2 separate DCDC channel 1 should be disabled using TDMDCE), */\ { 0x6163, "ctrl_attr"}, /* Total gain depending on INPLEV setting (channel 0), */\ { 0x6265, "zero_lvl"}, /* low noise gain switch zero trigger level , */\ { 0x62c1, "ctrl_fb_resistor"}, /* Select amplifier feedback resistor connection , */\ { 0x62e1, "lownoisegain_mode"}, /* ctrl select mode , */\ { 0x6305, "threshold_lvl"}, /* low noise gain switch trigger level , */\ { 0x6365, "hold_time"}, /* ctrl hold time before low audio is reckoned to be low audio, */\ { 0x6405, "lpm1_cal_offset"}, /* low power mode1 detector ctrl cal_offset from gain module , */\ { 0x6465, "lpm1_zero_lvl"}, /* low power mode1 zero crossing detection level , */\ { 0x64e1, "lpm1_mode"}, /* low power mode control , */\ { 0x6505, "lpm1_threshold_lvl"}, /* low power mode1 amplitude trigger level , */\ { 0x6565, "lpm1_hold_time"}, /* low power mode1 detector ctrl hold time before low audio is reckoned to be low audio, */\ { 0x65c0, "disable_low_power_mode"}, /* low power mode1 detector control , */\ { 0x6600, "dcdc_pfm20khz_limit"}, /* DCDC in PFM mode pwm mode is activated each 50us to force a pwm pulse, */\ { 0x6611, "dcdc_ctrl_maxzercnt"}, /* DCDC. Number of zero current flags to count before going to pfm mode, */\ { 0x6656, "dcdc_vbat_delta_detect"}, /* Threshold before booster is reacting on a delta Vbat (in PFM mode) by temporarily switching to PWM mode, */\ { 0x66c0, "dcdc_ignore_vbat"}, /* Ignore an increase on Vbat , */\ { 0x6700, "enbl_minion"}, /* Enables minion (small) power stage , */\ { 0x6713, "vth_vddpvbat"}, /* select vddp-vbat thres signal , */\ { 0x6750, "lpen_vddpvbat"}, /* select vddp-vbat filtred vs unfiltered compare , */\ { 0x6761, "ctrl_rfb"}, /* Feedback resistor selection - I2C direct mode , */\ { 0x6802, "tdm_source_mapping"}, /* tdm source mapping , */\ { 0x6831, "tdm_sourcea_frame_sel"}, /* Sensed value A , */\ { 0x6851, "tdm_sourceb_frame_sel"}, /* Sensed value B , */\ { 0x6871, "tdm_source0_clip_sel"}, /* clip information (analog /digital) for source0 , */\ { 0x6891, "tdm_source1_clip_sel"}, /* clip information (analog /digital) for source1 , */\ { 0x6a02, "rst_min_vbat_delay"}, /* rst_min_vbat delay (nb fs) , */\ { 0x6b00, "disable_auto_engage"}, /* disable auto engange , */\ { 0x6b10, "disable_engage"}, /* disable engange , */\ { 0x6c02, "ns_hp2ln_criterion"}, /* 0..7 zeroes at ns as threshold to swap from high_power to low_noise, */\ { 0x6c32, "ns_ln2hp_criterion"}, /* 0..7 zeroes at ns as threshold to swap from low_noise to high_power, */\ { 0x6c69, "spare_out"}, /* spare_out , */\ { 0x6d0f, "spare_in"}, /* spare_in , */\ { 0x6e10, "flag_lp_detect_mode1"}, /* low power mode 1 detection , */\ { 0x6e20, "flag_low_amplitude"}, /* low amplitude detection , */\ { 0x6e30, "flag_vddp_gt_vbat"}, /* vddp greater than vbat , */\ { 0x6f02, "cursense_comp_delay"}, /* delay to allign compensation signal with current sense signal, */\ { 0x6f40, "cursense_comp_sign"}, /* polarity of compensation for current sense , */\ { 0x6f50, "enbl_cursense_comp"}, /* enable current sense compensation , */\ { 0x6f72, "pwms_clip_lvl"}, /* set the amount of pwm pulse that may be skipped before clip-flag is triggered, */\ { 0x7033, "boost_cur"}, /* Max coil current , */\ { 0x7071, "bst_slpcmplvl"}, /* Slope compensation current, represents LxF (inductance x frequency) value , */\ { 0x7090, "boost_intel"}, /* Adaptive boost mode , */\ { 0x70a0, "boost_speed"}, /* Soft ramp up/down , */\ { 0x70e0, "dcdcoff_mode"}, /* DCDC on/off , */\ { 0x70f0, "dcdc_pwmonly"}, /* DCDC PWM only mode , */\ { 0x7104, "bst_drive"}, /* Binary coded drive setting for boost converter power stage, */\ { 0x7151, "bst_scalecur"}, /* For testing direct control scale current , */\ { 0x7174, "bst_slopecur"}, /* For testing direct control slope current , */\ { 0x71c1, "bst_slope"}, /* Boost slope speed , */\ { 0x71e0, "bst_bypass_bstcur"}, /* Bypass control for boost current settings , */\ { 0x71f0, "bst_bypass_bstfoldback"}, /* Bypass control for boost foldback , */\ { 0x7200, "enbl_bst_engage"}, /* Enable power stage dcdc controller , */\ { 0x7210, "enbl_bst_hizcom"}, /* Enable hiz comparator , */\ { 0x7220, "enbl_bst_peak2avg"}, /* Enable boost peak2avg functionality , */\ { 0x7230, "enbl_bst_peakcur"}, /* Enable peak current , */\ { 0x7240, "enbl_bst_power"}, /* Enable line of the powerstage , */\ { 0x7250, "enbl_bst_slopecur"}, /* Enable bit of max-current dac , */\ { 0x7260, "enbl_bst_voutcomp"}, /* Enable vout comparators , */\ { 0x7270, "enbl_bst_voutcomp86"}, /* Enable vout-86 comparators , */\ { 0x7280, "enbl_bst_voutcomp93"}, /* Enable vout-93 comparators , */\ { 0x7290, "enbl_bst_windac"}, /* Enable window dac , */\ { 0x72a5, "bst_windac"}, /* for testing direct control windac , */\ { 0x7300, "boost_alg"}, /* Control for boost adaptive loop gain , */\ { 0x7311, "boost_loopgain"}, /* DCDC boost loopgain setting , */\ { 0x7331, "bst_freq"}, /* DCDC boost frequency control , */\ { 0x7360, "bst_use_new_zercur_detect"}, /* Enable new zero current detection for boost control, */\ { 0x7430, "boost_track"}, /* Boost algorithm selection, effective only when boost_intelligent is set to 1, */\ { 0x7444, "boost_trip_lvl_1st"}, /* 1st Adaptive boost trip levels, effective only when DCIE is set to 1, */\ { 0x7494, "boost_hold_time"}, /* Hold time for DCDC booster, effective only when boost_intelligent is set to 1, */\ { 0x74e0, "sel_dcdc_envelope_8fs"}, /* Selection of data for adaptive boost algorithm, effective only when boost_intelligent is set to 1, */\ { 0x74f0, "ignore_flag_voutcomp86"}, /* Determines the maximum PWM frequency be the most efficient in relation to the Booster inductor value, */\ { 0x7534, "boost_trip_lvl_2nd"}, /* 2nd Adaptive boost trip levels, effective only when DCIE is set to 1, */\ { 0x7584, "boost_trip_lvl_track"}, /* Track Adaptive boost trip levels, effective only when boost_intelligent is set to 1, */\ { 0x75f0, "enbl_trip_hyst"}, /* Enable hysteresis on booster trip levels , */\ { 0x7635, "frst_boost_voltage"}, /* First boost voltage level , */\ { 0x7695, "scnd_boost_voltage"}, /* Second boost voltage level , */\ { 0x8001, "sel_clk_cs"}, /* Current sense clock duty cycle control , */\ { 0x8021, "micadc_speed"}, /* Current sense clock for MiCADC selection - 32/44.1/48 KHz Fs band only, */\ { 0x8050, "cs_gain_control"}, /* Current sense gain control , */\ { 0x8060, "cs_bypass_gc"}, /* Bypasses the CS gain correction , */\ { 0x8087, "cs_gain"}, /* Current sense gain , */\ { 0x8210, "invertpwm"}, /* Current sense common mode feedback pwm invert control, */\ { 0x8305, "cs_ktemp"}, /* Current sense temperature compensation trimming (1 - VALUE*TEMP)*signal, */\ { 0x8364, "cs_ktemp2"}, /* Second order temperature compensation coefficient , */\ { 0x8400, "cs_adc_bsoinv"}, /* Bitstream inversion for current sense ADC , */\ { 0x8421, "cs_adc_hifreq"}, /* Frequency mode current sense ADC , */\ { 0x8440, "cs_adc_nortz"}, /* Return to zero for current sense ADC , */\ { 0x8453, "cs_adc_offset"}, /* Micadc ADC offset setting , */\ { 0x8490, "cs_adc_slowdel"}, /* Select delay for current sense ADC (internal decision circuitry), */\ { 0x84a4, "cs_adc_gain"}, /* Gain setting for current sense ADC (two's complement), */\ { 0x8500, "cs_resonator_enable"}, /* Enable for resonator to improve SRN , */\ { 0x8510, "cs_classd_tran_skip"}, /* Skip current sense connection during a classD amplifier transition, */\ { 0x8530, "cs_inn_short"}, /* Short current sense negative to common mode , */\ { 0x8540, "cs_inp_short"}, /* Short current sense positive to common mode , */\ { 0x8550, "cs_ldo_bypass"}, /* Bypass current sense LDO , */\ { 0x8560, "cs_ldo_pulldown"}, /* Pull down current sense LDO, only valid if left_enbl_cs_ldo is high, */\ { 0x8574, "cs_ldo_voset"}, /* Current sense LDO voltage level setting (two's complement), */\ { 0x8700, "enbl_cs_adc"}, /* Enable current sense ADC , */\ { 0x8710, "enbl_cs_inn1"}, /* Enable connection of current sense negative1 , */\ { 0x8720, "enbl_cs_inn2"}, /* Enable connection of current sense negative2 , */\ { 0x8730, "enbl_cs_inp1"}, /* Enable connection of current sense positive1 , */\ { 0x8740, "enbl_cs_inp2"}, /* Enable connection of current sense positive2 , */\ { 0x8750, "enbl_cs_ldo"}, /* Enable current sense LDO , */\ { 0x8780, "enbl_cs_vbatldo"}, /* Enable of current sense LDO , */\ { 0x8790, "enbl_dc_filter"}, /* Control for enabling the DC blocking filter for voltage and current sense, */\ { 0x8801, "volsense_pwm_sel"}, /* Voltage sense source selection control , */\ { 0x8850, "vs_gain_control"}, /* Voltage sense gain control , */\ { 0x8860, "vs_bypass_gc"}, /* Bypasses the VS gain correction , */\ { 0x8870, "vs_igen_supply"}, /* Switch internal supply of current generator , */\ { 0x8887, "vs_gain"}, /* voltage sense gain , */\ { 0x8c00, "vs_adc_bsoinv"}, /* Bitstream inversion for voltage sense ADC , */\ { 0x8c40, "vs_adc_nortz"}, /* Return to zero for voltage sense ADC , */\ { 0x8c90, "vs_adc_slowdel"}, /* Select delay for voltage sense ADC (internal decision circuitry), */\ { 0x8d10, "vs_classd_tran_skip"}, /* Skip voltage sense connection during a classD amplifier transition, */\ { 0x8d30, "vs_inn_short"}, /* Short voltage sense negative to common mode , */\ { 0x8d40, "vs_inp_short"}, /* Short voltage sense positive to common mode , */\ { 0x8d50, "vs_ldo_bypass"}, /* Bypass voltage sense LDO , */\ { 0x8d60, "vs_ldo_pulldown"}, /* Pull down voltage sense LDO, only valid if left_enbl_cs_ldo is high, */\ { 0x8d74, "vs_ldo_voset"}, /* Voltage sense LDO voltage level setting (two's complement), */\ { 0x8f00, "enbl_vs_adc"}, /* Enable voltage sense ADC (Direct Control only only others done by manager), */\ { 0x8f10, "enbl_vs_inn1"}, /* Enable connection of voltage sense negative1 , */\ { 0x8f20, "enbl_vs_inn2"}, /* Enable connection of voltage sense negative2 , */\ { 0x8f30, "enbl_vs_inp1"}, /* Enable connection of voltage sense positive1 , */\ { 0x8f40, "enbl_vs_inp2"}, /* Enable connection of voltage sense positive2 , */\ { 0x8f50, "enbl_vs_ldo"}, /* Enable voltage sense LDO (Direct Control only only others done by manager), */\ { 0x8f80, "enbl_vs_vbatldo"}, /* Enable of voltage sense LDO (Direct Control only others done by manager), */\ { 0xa007, "mtpkey1"}, /* 5Ah, 90d To access KEY1_Protected registers (Default for engineering), */\ { 0xa107, "mtpkey2"}, /* MTP KEY2 register , */\ { 0xa200, "key01_locked"}, /* Indicates KEY1 is locked , */\ { 0xa210, "key02_locked"}, /* Indicates KEY2 is locked , */\ { 0xa302, "mtp_man_address_in"}, /* MTP address from I2C register for read/writing mtp in manual single word mode, */\ { 0xa330, "man_copy_mtp_to_iic"}, /* Start copying single word from mtp to I2C mtp register, */\ { 0xa340, "man_copy_iic_to_mtp"}, /* Start copying single word from I2C mtp register to mtp, */\ { 0xa350, "auto_copy_mtp_to_iic"}, /* Start copying all the data from mtp to I2C mtp registers, */\ { 0xa360, "auto_copy_iic_to_mtp"}, /* Start copying data from I2C mtp registers to mtp , */\ { 0xa400, "faim_set_clkws"}, /* Sets the faim controller clock wait state register, */\ { 0xa410, "faim_sel_evenrows"}, /* All even rows of the faim are selected, active high, */\ { 0xa420, "faim_sel_oddrows"}, /* All odd rows of the faim are selected, all rows in combination with sel_evenrows, */\ { 0xa430, "faim_program_only"}, /* Skip the erase access at wr_faim command (write-program-marginread), */\ { 0xa440, "faim_erase_only"}, /* Skip the program access at wr_faim command (write-erase-marginread), */\ { 0xa50f, "mtp_man_data_out_msb"}, /* MSB word of MTP manual read data , */\ { 0xa60f, "mtp_man_data_out_lsb"}, /* LSB word of MTP manual read data , */\ { 0xa70f, "mtp_man_data_in_msb"}, /* MSB word of write data for MTP manual write , */\ { 0xa80f, "mtp_man_data_in_lsb"}, /* LSB word of write data for MTP manual write , */\ { 0xb010, "bypass_ocpcounter"}, /* Bypass OCP Counter , */\ { 0xb020, "bypass_glitchfilter"}, /* Bypass glitch filter , */\ { 0xb030, "bypass_ovp"}, /* Bypass OVP , */\ { 0xb040, "bypass_uvp"}, /* Bypass UVP , */\ { 0xb050, "bypass_otp"}, /* Bypass OTP , */\ { 0xb060, "bypass_lost_clk"}, /* Bypass lost clock detector , */\ { 0xb070, "ctrl_vpalarm"}, /* vpalarm (uvp ovp handling) , */\ { 0xb087, "ocp_threshold"}, /* OCP threshold level , */\ { 0xb108, "ext_temp"}, /* External temperature (C) , */\ { 0xb190, "ext_temp_sel"}, /* Select temp Speaker calibration , */\ { 0xc000, "use_direct_ctrls"}, /* Direct control to overrule several functions for testing, */\ { 0xc010, "rst_datapath"}, /* Direct control for datapath reset , */\ { 0xc020, "rst_cgu"}, /* Direct control for cgu reset , */\ { 0xc038, "enbl_ref"}, /* Switch on the analog references, each part of the references can be switched on/off individually, */\ { 0xc0c0, "use_direct_vs_ctrls"}, /* voltage sense Direct control to overrule several functions for testing, */\ { 0xc0d0, "enbl_ringo"}, /* Enable the ring oscillator for test purpose , */\ { 0xc0e0, "use_direct_clk_ctrl"}, /* Direct clock control to overrule several functions for testing, */\ { 0xc0f0, "use_direct_pll_ctrl"}, /* Direct PLL control to overrule several functions for testing, */\ { 0xc100, "enbl_tsense"}, /* Temperature sensor enable control - I2C direct mode, */\ { 0xc110, "tsense_hibias"}, /* Bit to set the biasing in temp sensor to high , */\ { 0xc120, "enbl_flag_vbg"}, /* Enable flagging of bandgap out of control , */\ { 0xc20f, "abist_offset"}, /* Offset control for ABIST testing (two's complement), */\ { 0xc300, "bypasslatch"}, /* Bypass latch , */\ { 0xc311, "sourcea"}, /* Set OUTA to , */\ { 0xc331, "sourceb"}, /* Set OUTB to , */\ { 0xc350, "inverta"}, /* Invert pwma test signal , */\ { 0xc360, "invertb"}, /* Invert pwmb test signal , */\ { 0xc374, "pulselength"}, /* Pulse length setting test input for amplifier (clock d - k*2048*fs), */\ { 0xc3c0, "tdm_enable_loopback"}, /* TDM loopback test , */\ { 0xc400, "bst_bypasslatch"}, /* Bypass latch in boost converter , */\ { 0xc411, "bst_source"}, /* Sets the source of the pwmbst output to boost converter input for testing, */\ { 0xc430, "bst_invertb"}, /* Invert pwmbst test signal , */\ { 0xc444, "bst_pulselength"}, /* Pulse length setting test input for boost converter , */\ { 0xc490, "test_bst_ctrlsthv"}, /* Test mode for boost control stage , */\ { 0xc4a0, "test_bst_iddq"}, /* IDDQ testing in power stage of boost converter , */\ { 0xc4b0, "test_bst_rdson"}, /* RDSON testing - boost power stage , */\ { 0xc4c0, "test_bst_cvi"}, /* CVI testing - boost power stage , */\ { 0xc4d0, "test_bst_ocp"}, /* Boost OCP. For old ocp (ctrl_reversebst is 0), For new ocp (ctrl_reversebst is 1), */\ { 0xc4e0, "test_bst_sense"}, /* Test option for the sense NMOS in booster for current mode control., */\ { 0xc500, "test_cvi"}, /* Analog BIST, switch choose which transistor will be used as current source (also cross coupled sources possible), */\ { 0xc510, "test_discrete"}, /* Test function noise measurement , */\ { 0xc520, "test_iddq"}, /* Set the power stages in iddq mode for gate stress., */\ { 0xc540, "test_rdson"}, /* Analog BIST, switch to enable Rdson measurement , */\ { 0xc550, "test_sdelta"}, /* Analog BIST, noise test , */\ { 0xc570, "test_enbl_cs"}, /* Enable for digimux mode of current sense , */\ { 0xc580, "test_enbl_vs"}, /* Enable for digimux mode of voltage sense , */\ { 0xc600, "enbl_pwm_dcc"}, /* Enables direct control of pwm duty cycle for DCDC power stage, */\ { 0xc613, "pwm_dcc_cnt"}, /* Control pwm duty cycle when enbl_pwm_dcc is 1 , */\ { 0xc650, "enbl_ldo_stress"}, /* Enable stress of internal supply voltages powerstages, */\ { 0xc707, "digimuxa_sel"}, /* DigimuxA input selection control routed to DATAO (see Digimux list for details), */\ { 0xc787, "digimuxb_sel"}, /* DigimuxB input selection control routed to INT (see Digimux list for details), */\ { 0xc807, "digimuxc_sel"}, /* DigimuxC input selection control routed to PDMDAT (see Digimux list for details), */\ { 0xc981, "int_ehs"}, /* Speed/load setting for INT IO cell, clk or data mode range (see SLIMMF IO cell datasheet), */\ { 0xc9c0, "hs_mode"}, /* I2C high speed mode control , */\ { 0xca00, "enbl_anamux1"}, /* Enable anamux1 , */\ { 0xca10, "enbl_anamux2"}, /* Enable anamux2 , */\ { 0xca20, "enbl_anamux3"}, /* Enable anamux3 , */\ { 0xca30, "enbl_anamux4"}, /* Enable anamux4 , */\ { 0xca74, "anamux1"}, /* Anamux selection control - anamux on TEST1 , */\ { 0xcb04, "anamux2"}, /* Anamux selection control - anamux on TEST2 , */\ { 0xcb53, "anamux3"}, /* Anamux selection control - anamux on TEST3 , */\ { 0xcba3, "anamux4"}, /* Anamux selection control - anamux on TEST4 , */\ { 0xcd05, "pll_seli"}, /* PLL SELI - I2C direct PLL control mode only , */\ { 0xcd64, "pll_selp"}, /* PLL SELP - I2C direct PLL control mode only , */\ { 0xcdb3, "pll_selr"}, /* PLL SELR - I2C direct PLL control mode only , */\ { 0xcdf0, "pll_frm"}, /* PLL free running mode control; 1 in TCB direct control mode, else this control bit, */\ { 0xce09, "pll_ndec"}, /* PLL NDEC - I2C direct PLL control mode only , */\ { 0xcea0, "pll_mdec_msb"}, /* MSB of pll_mdec - I2C direct PLL control mode only, */\ { 0xceb0, "enbl_pll"}, /* Enables PLL in I2C direct PLL control mode only , */\ { 0xcec0, "enbl_osc"}, /* Enables OSC1M in I2C direct control mode only , */\ { 0xced0, "pll_bypass"}, /* PLL bypass control in I2C direct PLL control mode only, */\ { 0xcee0, "pll_directi"}, /* PLL directi control in I2C direct PLL control mode only, */\ { 0xcef0, "pll_directo"}, /* PLL directo control in I2C direct PLL control mode only, */\ { 0xcf0f, "pll_mdec_lsb"}, /* Bits 15..0 of PLL MDEC are I2C direct PLL control mode only, */\ { 0xd006, "pll_pdec"}, /* PLL PDEC - I2C direct PLL control mode only , */\ { 0xd10f, "tsig_freq_lsb"}, /* Internal sinus test generator frequency control , */\ { 0xd202, "tsig_freq_msb"}, /* Select internal sinus test generator, frequency control msb bits, */\ { 0xd230, "inject_tsig"}, /* Control bit to switch to internal sinus test generator, */\ { 0xd283, "tsig_gain"}, /* Test signal gain , */\ { 0xd300, "adc10_reset"}, /* Reset for ADC10 - I2C direct control mode , */\ { 0xd311, "adc10_test"}, /* Test mode selection signal for ADC10 - I2C direct control mode, */\ { 0xd332, "adc10_sel"}, /* Select the input to convert for ADC10 - I2C direct control mode, */\ { 0xd364, "adc10_prog_sample"}, /* ADC10 program sample setting - I2C direct control mode, */\ { 0xd3b0, "adc10_enbl"}, /* Enable ADC10 - I2C direct control mode , */\ { 0xd3c0, "bypass_lp_vbat"}, /* Bypass control for Low pass filter in batt sensor , */\ { 0xd409, "data_adc10_tempbat"}, /* ADC 10 data output data for testing , */\ { 0xd507, "ctrl_digtoana_hidden"}, /* Spare digital to analog control bits - Hidden , */\ { 0xd580, "enbl_clk_out_of_range"}, /* Clock out of range , */\ { 0xd621, "clkdiv_audio_sel"}, /* Audio clock divider selection in direct clock control mode, */\ { 0xd641, "clkdiv_muxa_sel"}, /* DCDC MUXA clock divider selection in direct clock control mode, */\ { 0xd661, "clkdiv_muxb_sel"}, /* DCDC MUXB clock divider selection in direct clock control mode, */\ { 0xd721, "datao_ehs"}, /* Speed/load setting for DATAO IO cell, clk or data mode range (see SLIMMF IO cell datasheet), */\ { 0xd740, "bck_ehs"}, /* High-speed and standard/fast mode selection for BCK IO cell (see IIC3V3 IO cell datasheet), */\ { 0xd750, "datai_ehs"}, /* High-speed and standard/fast mode selection for DATAI IO cell (see IIC3V3 IO cell datasheet), */\ { 0xd800, "source_in_testmode"}, /* tdm source in test mode (return only current and voltage sense), */\ { 0xd810, "gainatt_feedback"}, /* gainatt feedback to tdm , */\ { 0xd822, "test_parametric_io"}, /* test io parametric , */\ { 0xd850, "ctrl_bst_clk_lp1"}, /* boost clock control in low power mode1 , */\ { 0xd861, "test_spare_out1"}, /* test spare out 1 , */\ { 0xd880, "bst_dcmbst"}, /* dcm boost , */\ { 0xd8c3, "test_spare_out2"}, /* test spare out 1 , */\ { 0xee0f, "sw_profile"}, /* Software profile data , */\ { 0xef0f, "sw_vstep"}, /* Software vstep information , */\ { 0xf000, "calibration_onetime"}, /* Calibration schedule , */\ { 0xf010, "calibr_ron_done"}, /* Calibration Ron executed , */\ { 0xf020, "calibr_dcdc_api_calibrate"}, /* Calibration current limit DCDC , */\ { 0xf030, "calibr_dcdc_delta_sign"}, /* Sign bit for delta calibration current limit DCDC , */\ { 0xf042, "calibr_dcdc_delta"}, /* Calibration delta current limit DCDC , */\ { 0xf078, "calibr_speaker_info"}, /* Reserved space for allowing customer to store speaker information, */\ { 0xf105, "calibr_vout_offset"}, /* DCDC offset calibration 2's complement (key1 protected), */\ { 0xf169, "spare_mpt1_15_6"}, /* SPARE , */\ { 0xf203, "calibr_gain"}, /* HW gain module (2's complement) , */\ { 0xf245, "calibr_offset"}, /* Offset for amplifier, HW gain module (2's complement), */\ { 0xf2a5, "spare_mtp2_15_10"}, /* SPARE , */\ { 0xf307, "calibr_gain_vs"}, /* Voltage sense gain , */\ { 0xf387, "calibr_gain_cs"}, /* Current sense gain (signed two's complement format), */\ { 0xf407, "spare_mtp4_15_0"}, /* SPARE , */\ { 0xf487, "vs_trim"}, /* VS Trimming , */\ { 0xf50f, "calibr_R25C_R"}, /* Ron resistance of speaker coil , */\ { 0xf60f, "spare_mpt6_6_0"}, /* SPARE , */\ { 0xf706, "ctrl_offset_a"}, /* Offset of level shifter A , */\ { 0xf770, "spare_mtp7_07"}, /* SPARE , */\ { 0xf786, "ctrl_offset_b"}, /* Offset of amplifier level shifter B , */\ { 0xf7f0, "spare_mtp7_15"}, /* SPARE , */\ { 0xf806, "htol_iic_addr"}, /* 7-bit I2C address to be used during HTOL testing , */\ { 0xf870, "htol_iic_addr_en"}, /* HTOL I2C address enable control , */\ { 0xf884, "calibr_temp_offset"}, /* Temperature offset 2's compliment (key1 protected), */\ { 0xf8d2, "calibr_temp_gain"}, /* Temperature gain 2's compliment (key1 protected) , */\ { 0xf900, "mtp_lock_dcdcoff_mode"}, /* Disable function dcdcoff_mode , */\ { 0xf910, "spare_mtp9_1"}, /* SPARE , */\ { 0xf920, "mtp_lock_bypass_clipper"}, /* Disable function bypass_clipper , */\ { 0xf930, "mtp_lock_max_dcdc_voltage"}, /* Force Boost in follower mode , */\ { 0xf943, "calibr_vbg_trim"}, /* Bandgap trimming control , */\ { 0xf980, "spare_mtp9_8"}, /* SPARE , */\ { 0xf990, "mtp_enbl_pwm_delay_clock_gating"}, /* pwm delay clock auto gating , */\ { 0xf9a0, "mtp_enbl_ocp_clock_gating"}, /* ocpclock auto gating , */\ { 0xf9b0, "mtp_gate_cgu_clock_for_test"}, /* cgu test clock control , */\ { 0xf9c0, "mtp_tdm_pad_sel"}, /* tdm pad selection , */\ { 0xf9d2, "spare_mtp9_15_12"}, /* MTP-control FW - See Firmware I2C API document for details, */\ { 0xfa0f, "mtpdataA"}, /* MTPdataA (key1 protected) , */\ { 0xfb0f, "mtpdataB"}, /* MTPdataB (key1 protected) , */\ { 0xfc0f, "mtpdataC"}, /* MTPdataC (key1 protected) , */\ { 0xfd0f, "mtpdataD"}, /* MTPdataD (key1 protected) , */\ { 0xfe0f, "mtpdataE"}, /* MTPdataE (key1 protected) , */\ { 0xff07, "calibr_osc_delta_ndiv"}, /* Calibration data for OSC1M, signed number representation, */\ { 0xff87, "spare_mtp7_15_08"}, /* SPARE , */\ { 0xffff,"Unknown bitfield enum" } /* not found */\ }; enum tfa9874_irq { tfa9874_irq_stvdds = 0, tfa9874_irq_stbstoc = 1, tfa9874_irq_stotds = 2, tfa9874_irq_stocpr = 3, tfa9874_irq_stuvds = 4, tfa9874_irq_stmanalarm = 5, tfa9874_irq_sttdmer = 6, tfa9874_irq_stnoclk = 7, tfa9874_irq_max = 8, tfa9874_irq_all = -1 /* all irqs */}; #define TFA9874_IRQ_NAMETABLE static tfaIrqName_t Tfa9874IrqNames[]= {\ { 0, "STVDDS"},\ { 1, "STBSTOC"},\ { 2, "STOTDS"},\ { 3, "STOCPR"},\ { 4, "STUVDS"},\ { 5, "STMANALARM"},\ { 6, "STTDMER"},\ { 7, "STNOCLK"},\ { 8, "8"},\ }; #endif /* _TFA9874_TFAFIELDNAMES_H */