/*this is for different project dtsi*/
&op_wlchg {
	status = "okay";
	op,max-voltage-mv = <4550>;
	op,fastchg-curr-max-ma = <1500>;
	op,fastchg-curr-min-ma = <400>;
	op,fastchg-vol-entry-max-mv = <4380>;
	op,fastchg-vol-normal-max-mv = <4480>;
	op,fastchg-vol-hot-max-mv = <4130>;
	op,fastchg-vol-min-mv = <3300>;
	op,fastchg-temp-max = <430>;
	op,fastchg-temp-min = <120>;
	op,fastchg-soc-max = <85>;
	op,fastchg-soc-min = <1>;
	op,fastchg-soc-mid = <75>;
	op,fastchg-discharge-curr-max = <2000>;
	/*
	 * | temp_min | temp_max | target_curr_ua | vol_max_mv |need wait |
	 *
	 * temp_min: Switch to the previous level when the temperature is lower
	 *           than this value. If it is 0, do not switch.
	 * temp_max: Switch to the next level when the temperature is greater
	 *           than this value
	 * target_curr_ua: Target current in this temperature range.
	 * vol_max_mv: Maximum battery voltage.
	 * need wait: 1:Need wait for a while after switching to the next level.
	 *            0:No need to wait after switching to the next level.
	 */
	op,fastchg-ffc_step = <0   405  1500000 4420 1
			       380 420  1000000 4450 1
			       390 420  850000  4480 1
			       400 420  625000  4480 0>;
	/* ibatmax setting for different temp regions */
	op,epp-ibatmax-ma = <0 1000 2500 2500 2500 2500 1500 0>;
	op,bpp-ibatmax-ma = <0 1000 1500 1500 1500 1500 1500 0>;
	op,bpp-sdp-ibatmax-ma = <0 1000 1000 1000 1000 1000 1000 0>;
	op,epp-iclmax-ma = <0 300 1100 1100 1100 1100 650 0>;
	op,bpp-iclmax-ma = <0 500 1000 1000 1000 1000 1000 0>;
	op,bpp-sdp-iclmax-ma = <0 500 500 500 500 500 500 0>;
	op,fastchg-ibatmax-ma = <4000 6000>;
	/* temp region settings */
	cold-bat-decidegc = <20>;
	little-cold-bat-decidegc = <0>;
	cool-bat-decidegc = <50>;
	little-cool-bat-decidegc = <120>;
	pre-normal-bat-decidegc = <160>;
	warm-bat-decidegc = <440>;
	hot-bat-decidegc = <500>;

	cool-vbat-thr-mv = <4180>;
	cool-epp-ibat-ma = <1500>;
	cool-epp-icl-ma = <650>;
	/* deviation check */
	op,rx-freq-threshold = <129>;

	/*wireless charge skin-therm*/
	fastchg-skin-temp-max = <420>;
	fastchg-skin-temp-min = <400>;
	epp-skin-temp-max = <390>;
	epp-skin-temp-min = <370>;
	op,epp-curr-step = <1100 550>;

	/* fod parameter*/
	op,fastchg-fod-enable;
	op,fastchg-match-q-new = /bits/ 8 <0x56>;
	op,fastchg-match-q = /bits/ 8 <0x44>;
	op,fastchg-fod-parm-new = /bits/ 8 <0xac 0x32 0xac 0x28 0xa0 0xba
					0x9a 0xd3 0x9a 0xce 0x9f 0xf6>;
	op,fastchg-fod-parm = /bits/ 8 <0xac 0x32 0xac 0x28 0xa0 0x1e
					0x9a 0x37 0x9a 0x32 0x9f 0xc4>;
	op,fastchg-fod-parm-startup = /bits/ 8 <0xac 0x7f 0xac 0x28 0xa0 0x1e
						0x9a 0x37 0x9a 0x32 0x9f 0xc4>;

	/* vbatdet setting for different temp regions */
	vbatdet-mv = <0 3675 4235 4370 4370 4370 4030 0>;
};

&op_wlchg_rx {
	status = "okay";
};

&op_wlchg_cp1 {
	status = "okay";
};

&op_wlchg_cp2 {
	status = "okay";
};

&op_wlchg_gpio {
	status = "okay";
};

&op_wlchg_pm8250_gpio {
	status = "okay";
};

&op_wlchg_pm8150a_gpio {
	status = "okay";
};

&pm8150b_pdphy {
	pinctrl-names = "default";
	pinctrl-0 = <&vbus_gpio_default>;
	otg-use_external_boost;
	otg_en-gpio = <&pm8150l_gpios 4 0x00>;
	vbus-gpio = <&tlmm 172 0x00>;
};

/* @bsp, Battery & Charging config START */
//&kona_mtp_batterydata {
//	#include "OP-fg-batterydata-4510mah.dtsi"
//};
/* @bsp, Battery & Charging config END */

//&usb1 {
//	status = "disabled";
//};

//&vendor {
//	extcon_usb1 {
//		status = "disabled";
//	};
//};