#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>

#include "pm8150.dtsi"
#include "pm8150b.dtsi"
#include "pm8150l.dtsi"
#include "pm8009.dtsi"

&spmi_bus {
	#address-cells = <2>;
	#size-cells = <0>;
	interrupt-controller;
	#interrupt-cells = <4>;

	qcom,pmxprairie@8 {
		compatible = "qcom,spmi-pmic";
		reg = <0x8 SPMI_USID>;
		#address-cells = <2>;
		#size-cells = <0>;

		qcom,power-on@800 {
			compatible = "qcom,qpnp-power-on";
			reg = <0x800 0x100>;
			qcom,modem-reset;
		};
	};

	qcom,pmxprairie@9 {
		compatible ="qcom,spmi-pmic";
		reg = <0x9 SPMI_USID>;
		#address-cells = <2>;
		#size-cells = <0>;
	};
};

&pm8150_gpios {
	key_home {
		key_home_default: key_home_default {
			pins = "gpio1";
			function = "normal";
			input-enable;
			bias-pull-up;
			power-source = <0>;
		};
	};

	key_vol_up {
		key_vol_up_default: key_vol_up_default {
			pins = "gpio6";
			function = "normal";
			input-enable;
			bias-pull-up;
			power-source = <1>;
		};
	};
	//#ifdef OPLUS_FEATURE_TP_BASIC
	key_vol_down {
		key_vol_down_default: key_vol_down_default {
			pins = "gpio7";
			function = "normal";
			input-enable;
			bias-pull-up;
			power-source = <1>;
		};
	};
	//#endif

	key_confirm {
		key_confirm_default: key_confirm_default {
			pins = "gpio7";
			function = "normal";
			input-enable;
			bias-pull-up;
			power-source = <0>;
		};
	};

	usb2_vbus_boost {
		usb2_vbus_boost_default: usb2_vbus_boost_default {
			pins = "gpio9";
			function = "normal";
			output-low;
			power-source = <1>;	/* 1.8V input supply */
		};
	};

	usb2_vbus_det {
		usb2_vbus_det_default: usb2_vbus_det_default {
			pins = "gpio10";
			function = "normal";
			input-enable;
			bias-pull-down;
			power-source = <1>;	/* 1.8V input supply */
		};
	};
};

&pm8150b_gpios {
	qnovo_fet_ctrl {
		qnovo_fet_ctrl_state1: qnovo_fet_ctrl_state1 {
			pins = "gpio8";
			function = "normal";
			input-enable;
			output-disable;
			bias-disable;
			power-source = <0>;
		};

		qnovo_fet_ctrl_state2: qnovo_fet_ctrl_state2 {
			pins = "gpio8";
			function = "normal";
			input-enable;
			output-disable;
			bias-pull-down;
			power-source = <0>;
		};
	};

	smb_stat {
		smb_stat_default: smb_stat_default {
			  pins = "gpio6";
			  function = "normal";
			  input-enable;
			  bias-pull-up;
			  qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
			  power-source = <0>;
		  };
	};
};

&pm8150b_qnovo {
	pinctrl-names = "q_state1", "q_state2";
	pinctrl-0 = <&qnovo_fet_ctrl_state1>;
	pinctrl-1 = <&qnovo_fet_ctrl_state2>;
};

&pm8150b_fg {
	nvmem-names = "fg_sdam";
	nvmem = <&pm8150_sdam_2>;
};

&pm8150b_charger {
	dpdm-supply = <&usb2_phy0>;
	smb5_vconn: qcom,smb5-vconn {
		regulator-name = "smb5-vconn";
	};

	smb5_vbus: qcom,smb5-vbus {
		regulator-name = "smb5-vbus";
	};
};

&pm8150b_pdphy {
	vdd-pdphy-supply = <&pm8150_l2>;
	vbus-supply = <&smb5_vbus>;
	vconn-supply = <&smb5_vconn>;
};

&pm8150b_gpios {
	haptics_boost {
		haptics_boost_default: haptics_boost_default {
			pins = "gpio5";
			function = "normal";
			output-enable;
			input-disable;
			bias-disable;
			qcom,drive-strength = <3>; /* high */
			power-source = <1>; /* 1.8 V */
		};
	};
};

&soc {
	vreg_tof: regulator-dbb1 {
		compatible = "regulator-fixed";
		regulator-name = "vdd_tof";
		regulator-min-microvolt = <3600000>;
		regulator-max-microvolt = <3600000>;
		gpio = <&pm8009_gpios 1 GPIO_ACTIVE_HIGH>;
		startup-delay-us = <1000>;
		enable-active-high;
	};

	vreg_hap_boost: regulator-haptics-boost {
		compatible = "regulator-fixed";
		regulator-name = "vdd_hap_boost";
		gpio = <&pm8150b_gpios 5 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&haptics_boost_default>;
		startup-delay-us = <1000>;
		enable-active-high;
		status = "disabled";
	};
};

&usb0 {
	extcon = <&pm8150b_pdphy>, <&eud>;
};

&usb_qmp_dp_phy {
	 extcon = <&pm8150b_pdphy>;
};

&sde_dp {
	extcon = <&pm8150b_pdphy>;
};